SIPOS SEVEN 2SA7 - Page 121

Y070.302/EN Page 121
Operation instructions
SIPOS SEVEN: PROFITRON, HiMod
16
Index
16 Index
Program speeds. .................... 40
Proportional move. ................... 81
Proportional/split range function.
....................... refer to Options
Q
Quick start. ...................... 90, 91
Quick start/stop. ..................... 90
R
Read commissioning data. ............. 30
Recognition
Open circuit analog input. ............ 88
Recommended spare parts. ........... 113
Record torque curve. ................. 99
Recycling. ........................... 5
Reduction ratio. ..................... 47
Relay board. ......................... 8
Remote. ........................... 28
Remote control. .................... 107
Bluetooth. ....................... 108
COM-SIPOS. ..................... 107
Remote control unit. ................ 96
Separate mounting. ................. 14
Remote control unit. .................. 96
Retry torque block. ................... 65
Revs/stroke. ............see Signaling gear
Rise time. .......................... 87
Rotary push button. .................. 23
Rotate display representation. .......... 93
Runtime monitoring. .................. 90
S
Safety instructions. .................... 4
Safety relevant parameters. ............ 77
Behavior on loss of signal. ........... 78
EMERGENCY input. ................ 77
EMERGENCY position. .............. 78
EMERGENCY speed. ............... 77
SavedataonUSBashdrive. ......... 109
SaveparametersonUSBashdrive. ... 109
Select additional gear. ................ 37
Select closing direction. ............ 40, 64
Select language. ..................... 29
Separate assembly. ............... 14, 84
Separate mounting
Cable lengths. ..................... 14
Connections. ...................... 14
Parameter. . . . . . . . . . . . . . . . . . . . . . . . . 84
Specication. ...................... 14
Serial number. .................. 82, 101
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Set clock. .......................... 95
Set cut-off modes and tripping torques. 42, 64
Set display. ......................... 94
Set standby time. .................... 95
Setting
Functions. ........................ 61
Language. ..........see Display language
Maintenance intervals of valve. ........ 86
Mechanical position indicator. ......... 55
Real time clock. .................... 95
Standby time. ..................... 95
Valve-specicparameters. ........... 62
Setting range. ....................... 51
Signaling gear. ....................... 7
General information. ................ 45
Prerequisite for adjustment. .......... 47
Transmission ratio. ................. 47
Transmission ratio adjustment. ........ 47
Valve travel. ....................... 47
Software functions. ................... 78
Enable customer variants. . . . . . . . . . . . . 79
Enable software functions. ........... 79
Spare parts. ....................... 113
Special parameters. .................. 83
Autom. TL adapt. end position. ........ 91
Check maintenance. ................ 86
Close tightly. ...................... 87
DC brake. ........................ 87
DC link voltage limitation. ............ 89
DCS acceptance time. .............. 92
Delay of Power failure message. ...... 88
End position speed. . . . . . . . . . . . . . . . . . 90
Intermediate contact. . . . . . . . . . . . . . . . . 84
Maintenance intervals of valve. ........ 86
Motor heating on/off. ................ 85
Motor protection on/off. .............. 85
Motor warning. .................... 85
Rise time. ........................ 87
Runtime monitoring. ................ 90
Separate mounting. ................. 84
Tag number. ...................... 84
Test operation. . . . . . . . . . . . . . . . . . . . . . 89
Threshold open circuit Analog input. .... 88
Torquemeasurementange. ......... 88
Speed adjustment. ................ 41, 64
Speed in end positions. ............... 90
Standby screen. ..................... 94
Start menu. ......................... 26
Status indication. ................. 16, 18
Status messages. .................... 18
Stem protection tube. ................. 11
Storage. ............................ 5