2 • List of Figures
_____________________________________________________________________________________________
HRVS-DN Instruction and Commissioning Manual
Table of Contents
1. List of Figures ........................................................................................................................... 6
2. Safety & Warnings .................................................................................................................... 8
2.1 Safety .......................................................................................................................................... 8
2.2 Attention ...................................................................................................................................... 8
2.3 Warnings ..................................................................................................................................... 8
3. Introduction ............................................................................................................................... 9
3.1 Why Solcon? Why Soft Starters? ................................................................................................ 9
3.2 How Soft Starters Work? .......................................................................................................... 10
Main Features, Options and Advantages ........................................................................................ 11
4. Technical Data ........................................................................................................................ 13
4.1 HRVS-DN IP00 Unit (OEM Kit) ................................................................................................. 13
4.2 Typical Connection of the HRVS-DN IP00 Unit (OEM Kit) ....................................................... 14
4.3 Typical Connection of the HRVS-DN in a Cabinet .................................................................... 15
4.3.1 Typical Connection of HRVS-DN up to 6.6kV ............................................................... 15
4.3.2 Typical Connection of HRVS-DN from 10kV and up. .................................................... 16
4.4 HRVS-DN Selection .................................................................................................................. 17
4.4.1 Motor Current and Starting Conditions .......................................................................... 17
4.4.2 PIV (Peak Inverse Voltage) ........................................................................................... 17
4.4.3 Rated Currents Frame Sizes ......................................................................................... 18
4.5
Ordering Information ................................................................................................................. 19
4.5.1 Ordering IP00 Unit (OEM kit) ........................................................................................ 19
4.5.2 Ordering a Cabinet Installed Soft Starter ...................................................................... 21
4.6 Power Connections Description ................................................................................................ 23
4.7 Control Connections Description .............................................................................................. 24
4.7.1 Input Terminal 7 - Test/Reset/MULTI SOFT STOP ....................................................... 30
4.7.2 Input Terminal 8 - Dual Adjust/Reset ............................................................................ 30
4.7.3 Output Terminals 10, 11 & 12 – Immediate/# Strts PreAlarm ....................................... 30
5. Recommended Wiring Diagrams .......................................................................................... 31
5.1 Control Supply and Control Inputs From a Single Source ........................................................ 31
5.2 Separate Sources for Control Supply and Control Inputs ......................................................... 31
5.3 Three Separate Sources for Control Supply and Control Inputs ............................................... 32
5.4 Soft Start and Immediate Stop (No Soft Stop) .......................................................................... 32
5.5 Soft Start and Soft Stop wiring .................................................................................................. 33
5.6 Soft Start, Soft Stop and Immediate Stop Wiring ...................................................................... 33
5.7 Soft Start, Soft Stop and Stop ................................................................................................... 34
5.8 External Fault ............................................................................................................................ 34
5.9 Dual Adjustment (Control Input #8) ........................................................................................... 34
5.10Bypass Contactor ...................................................................................................................... 35
5.11Operating via Communication Links ......................................................................................... 36
5.12Control Input #7 ........................................................................................................................ 37
5.13Control Input #8 ........................................................................................................................ 37
6. Installation of IP00 (OEM Kit) in a Cabinet ........................................................................... 38
6.1 Mounting ................................................................................................................................... 38
6.1.1 Low Voltage Section ...................................................................................................... 39
6.2 Temperature Range & Heat Dissipation ................................................................................... 39
6.3 Control Module Main PCB and Optional PCBs ......................................................................... 40
6.4 Dip Switch Settings on the Main PCB ....................................................................................... 40
6.4.1 Switch # 1 – Display Modes .......................................................................................... 40
6.4.2 Switch # 2 – Tacho Feedback (0-10VDC) ..................................................................... 41
6.4.3 Switches # 4, 5 & 6 – Language Selection ................................................................... 41
6.4.4 Switch # 7 – Extended Settings ..................................................................................... 42
6.4.5 Switch # 8 – Software Lock ........................................................................................... 42
6.5 Analog I/O (Option 5) (Terminals Gnd, Out (-), Out (+)) .......................................................... 43
To Next Page
Loading...
Need help?
General
