7 • List of Figures
_______________________________________________________________________________________________
Figure 5 – Voltage Increase .............................................................................................................................. 10
Figure 6 – Torque Reduction ............................................................................................................................. 10
Figure 7 – Current Limit ..................................................................................................................................... 10
Figure 8 – HRVS-DN IP00 Unit (OEM Kit) ........................................................................................................ 13
Figure 9 – Typical Connection of HRVS-DN IP00 Unit (OEM Kit) ..................................................................... 14
Figure 10 – Typical Connection of HRVS-DN up to 6.6kV with Line Contactor and Bypass Contactor ............ 15
Figure 11 – Typical Connection of HRVS-DN from 10kV and up With Line Contactor and Bypass Contactor . 16
Figure 12 – HRVS-DN up to 6.6kV Power Section ............................................................................................ 23
Figure 13 – Control Module Input/Output .......................................................................................................... 29
Figure 14 – HRVS-DN up to 6.6kV - Phase Disassembly Accessories ............................................................. 38
Figure 15 - HRVS-DN Control Module .............................................................................................................. 40
Figure 16 – Optional Analog PCB ..................................................................................................................... 43
Figure 17 – Optional Insulation PCB Wiring ...................................................................................................... 44
Figure 18 – RU-7, Resistor Unit – Dimensional Drawing .................................................................................. 44
Figure 19 - Remote Key Pad, Connection Cable and Control Module. ............................................................. 45
Figure 20 - Remote Key Pad - Dimensions ....................................................................................................... 45
Figure 21 - Remote Key Pad - Mechanical Installation and Cut-out Dimensions ............................................. 46
Figure 22 - HRVS-DN Control Keypad .............................................................................................................. 47
Figure 23 – Eye Bolts Location on Top of the Cabinet ...................................................................................... 84
Figure 24 – Cabinet Lifting Using 4 Lifting Cables. Top angle, A, Should be ≤60° .......................................... 85
Figure 25 – Anchor Bolts Holes Location on the Base of the Cabinet at Level 0mm. ....................................... 85
Figure 26 – Power and Control Cables Penetration to the Cabinet at Level 75mm .......................................... 86
Figure 27 – Power Cables Connection and Control Cables Routing. ................................................................ 86
Figure 28 – HRVS-DN up to 6.6kV Standard Cabinet – One Line Diagram ...................................................... 88
Figure 29 - HRVS-DN up to 6.6kV Standard Cabinet – Doors Closed .............................................................. 89
Figure 30 - HRVS-DN up to 6.6kV Standard Cabinet – Doors Open ................................................................ 89
Figure 31 – HRVS-DN from 10kV and up, Standard Cabinet – One Line Diagram .......................................... 90
Figure 32 - HRVS-DN from 10kV and up Standard Cabinet – Doors Closed .................................................... 91
Figure 33 - HRVS-DN from 10kV and up Standard Cabinet – Doors Open ...................................................... 91
Figure 34 - HRVS-DN Low Voltage Compartment ............................................................................................ 92
Figure 35 – Power Supply to Firing PCB (HRVS-DN Models up to 6600V). ..................................................... 93
Figure 36 – Power Supply to Firing PCB (HRVS-DN Models From 10000V and up) ........................................ 94
Figure 37 – EPT-Rx Fuse Replacement Procedure .......................................................................................... 94
Figure 38 - HRVS-DN - Typical Control Wiring of Standard Cabinet ............................................................... 95
Figure 39 – HRVS-DN up to 6.6kV – Preparations for High-pot Test .............................................................. 100
Figure 40 – HRVS-DN up to 6.6kV – EPT-Tx not Connected Preparations for High-pot Test, Testing L1 ..... 101
Figure 41 – HRVS-DN up to 6.6kV – EPT-Tx not Connected Preparations for High-pot Test, Testing L2 ..... 102
+Figure 42 – HRVS-DN up to 6.6kV – EPT-Tx not Connected Preparations for High-pot Test, Testing L3 ... 102
Figure 43 – HRVS-DN from 10kV and Up – Preparations for High-pot Test ................................................... 103
Figure 44 – HRVS-DN from 10kV and up, EPT-Tx not Connected, Preparations for High-pot Test, Testing L1
................................................................................................................................................................. 104
Figure 45 – HRVS-DN from 10kV and up, EPT-Tx not Connected, Preparations for High-pot Test, Testing L2
................................................................................................................................................................. 105
Figure 46 – HRVS-DN from 10kV and up, EPT-Tx not Connected, Preparations for High-pot Test, Testing L3
................................................................................................................................................................. 105
Figure 47 – Current Gain Dip Switches Location ............................................................................................ 110
Figure 48 – HRVS-DN up to 6.6kV – EPT-Tx and Test Harness .................................................................... 111
Figure 49 – HRVS-DN From 10kV and up – EPT-Tx and Test Harness ......................................................... 111
Figure 50 – Firing PCB – SCR#1 Gate-Cathode Testing ................................................................................ 120
Figure 51 – DPV0 parameters (Cyclic parameters) ......................................................................................... 150
Figure 52 – Updating the register number that will show at DPV0 (by Data Request) .................................... 152
Figure 53 – Reading the register number that is shown in the DPV0 (cyclic) list ............................................ 153
Figure 54 – Choosing register number 80 hex ................................................................................................ 154
Figure 55 – Reading 4 following register by Data Request (DPV1) ................................................................ 155
Figure 57 - Data rate (Baud rate) rotary switch layout ..................................................................................... 165
To Next Page
Loading...
Need help?
General
