SmartPAC 2 User Manual 1126700
Index I-5
security
access settings
,4-25
access types,4-25
changing passwords,4-28
setting access privileges,4-24
sensor summary, viewing,5-30
sensor-disabled output, wiring,2-31
sensors (die protection)
adjusting the ready signal for green sensors
,6-9
adjusting the stroke preset for green special
sensors
,6-9
changing sensor settings,5-30
deleting a sensor,5-31
enabling/disabling, 5-51, 6-6
faults,7-8
naming,5-22
programming, 5-16, 5-20, 5-32
programming the ready signal for green
sensors
, 5-27, 5-32
programming the stroke preset for green special
sensors
, 5-29, 5-35
sensor terminology,5-16
sensors available from Wintriss,1-5
setting enable mode,4-18
setting sensor type,5-24
setting stop type,5-25
setting the auto enable by sensor counter,5-23
setting the auto enable by tool counter,5-21
setting the critical angle for sensors set to smart
stop
,5-26
turning a sensor on or off,5-52
types,5-17
viewing actual on/off angles,6-10
viewing sensor settings,5-30
viewing sensor status, 5-51, 6-12
viewing the sensor summary, 5-30, 6-12
setup mode
enabling
,4-20
enabling/disabling counters,4-6
wiring circuit,2-31
SFC (ShopFloorConnect Asset Utilization
Software)
reporting downtime to
,F-1
reporting good parts count to,F-22
reporting scrap count to,F-22
setting communications with SmartPAC 2,F-7
slow RPM, setting,4-13
smart stop, setting as sensor stop type,5-25
SmartPAC 1, upgrading to SmartPAC 2,D-1
SmartPAC 2 board layout,2-13
SmartView
changing IP address type
,C-4
changing network settings,C-4
enabling,4-35, C-2
enabling e-mail,C-2
installing,C-6
network requirements,C-1
operation,C-10
programming network settings,C-2
selecting press type,C-2
sending remote messages,C-13
setting up e-mail,C-2
setting up the network,C-1
using the main page,C-11
using the ping utility,C-15
using the press status information page,C-12
using the setup page,C-10
specifications, SmartPAC 2,1-7
speed (press)
adjusting programmed maximum and minimum
limits
,6-27
configuring high-speed version of SmartPAC
2
,2-41
faults,7-10
programming maximum and minimum
limits
,5-48
start time
fault (loss of rotation)
,7-3
viewing,6-19
start time limit
setting
,4-8
viewing,6-19
status (sensor), viewing, 5-51, 6-12
stop circuits
running in conduit
,2-16
wiring,2-15
stop time
determining using the ninety-degree (90°) stop-
time test
,6-19
faults,7-6
viewing,6-19
stop time limit
calculating
,4-9
setting,4-8
viewing,6-19
stop type (sensor), setting,5-25
stopping angle, viewing,6-19
stroke preset
adjusting for green special sensors
,6-9
programming for green special sensors,5-29,
5-35
suppressors, installing,2-30
–T–
test tool, creating and loading,2-41
tests. See checkout tests, performing
time, setting
,4-41
toggle, setting batch counter output mode to,5-13
tool information
abbreviations for units
,4-23
changing tool parameters,6-28
decimal place formats,4-23
entering tool parameters,5-49
setting formats for,4-20
tool number mode, setting,4-4
tool template, copying to a new tool,5-5
To Next Page
Loading...
Need help?
General
