1126700 SmartPAC 2 User Manual
I-4 Index
faults,7-3
installing,2-37
testing for faults,2-42
wiring,2-40
power, turning on to SmartPAC 2,2-33
presets (counter)
preset reached messages
,7-2
setting and clearing,5-11
press
adjusting speed limits
,6-27
selecting press type in SmartView,C-2
setting press name,4-8
setting press type,4-38
setting SmartPAC 2 for use with a link-motion
press
,4-42
setting speed limits,5-48
setting the start time limit,4-8
setting the stop time limit,4-8
viewing the start time,6-19
viewing the start time limit,6-19
viewing the stop time,6-19
viewing the stop time limit,6-19
viewing the stopping angle,6-19
preventive maintenance (PM) monitor
assigning a new password
,A-8
clearing an alert,A-14
entering the password,A-4
initializing,A-6
installing,A-3
making Initialization settings,A-4
modifying the tracking frequency in Run
mode
,A-14
operation,A-2
selecting PM item names,A-8
setting tracking frequency,A-11
setting tracking units,A-10
using in Run mode,A-12
viewing PM status,A-13
ProCamPAC
adding or upgrading
,2-18
board layouts,2-20
installing new board,2-21
replacing board,2-18
testing cam channels,2-42
verifying installation,2-34
ProCamPAC output assembly
board layout
,2-27
connecting relays to equipment,2-29
installing diodes,2-30
mounting,2-25
running wiring in conduit,2-25
selecting relays for cam channels,2-25
wiring,2-25
Program mode
entering and exiting
,5-1
main menu,5-1
navigation,3-19
overview,3-18
Program/Run key switch (SmartPAC 2),
using
,3-10
pulse
setting batch counter output mode to
,5-13
setting duration of pulsed batch counter
output
,5-13
–R–
ready signal
adjusting for green sensors
,6-9
overview,5-17
programming for green sensors, 5-27, 5-32
red sensors
faults
,7-10
overview,5-18
selecting as sensor type,5-24
relays, cam output
connecting to equipment
,2-29
installing diodes,2-30
installing suppressors,2-30
selecting for each channel,2-25
remote messages, sending in SmartView,C-13
remote reset switch, wiring,2-31
RESET key (SmartPAC 2), using,3-10
resolver
checking/setting direction of rotation
,2-42
faults,7-3
installing,2-10
mounting,2-11
principle of operation,1-4
running wiring in conduit,2-12
wiring,2-12
zeroing, 2-35, 4-2
response time, Shadow light curtains,6-23
restore (tool and initialization data),
performing
,4-29
Run mode
entering and exiting
,6-2
main menu,6-1
navigation,3-21
overview,3-20
–S–
safety distance
calculating using the ANSI formula
,6-23
calculating using the OSHA formula,6-25
increasing for floating or blanking windows,6-26
SBR (SmartPAC Backup and Restore)
using to back up tool settings in SmartPAC
1
,D-1
using to restore SmartPAC 1 tool settings to
SmartPAC 2
,D-12
scrap count, reporting to LETS,G-19
scrap count, reporting to SFC,F-22
screens (SmartPAC 2)
e-mailing screen captures
,3-22
layout,3-12
making screen captures,3-22
To Next Page
Loading...
Need help?
General
