EasyManua.ls Logo

YASKAWA L1000A - Page 361

YASKAWA L1000A
522 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
8.4 Option Card Installation
YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual 361
Peripheral Devices &
Options
8
Wire Gauges and Tightening Torques
Wire gauge and torque specifications are listed in Table 8.4. For simpler and more reliable wiring, use crimp ferrules on
the wire ends. Refer to the option manuals for the wire size and torque specifications of other options.
Table 8.4 Wire Gauges and Tightening Torques
Crimp Terminals
Yaskawa recommends using CRIMPFOX 6 by Phoenix Contact or equivalent crimp terminals with the specifications
listed in Table 8.5 for wiring to ensure proper connections.
Note: Properly trim wire ends so loose wire ends do not extend from the crimp terminals.
Table 8.5 Crimp Terminal Sizes
PG Encoder Cables for PG-B3 Option
Yaskawa recommends using a LMA-B-S185Y (complementary output) for cables running between the PG-B3
Option and the PG as show in Figure 8.11.
For instructions on wiring the terminal block, refer to Table 8 .3.
Figure 8.10
Figure 8.11 Wiring PG Encoder Cable
Table 8.6 Connecting the PG Encoder Cable Specification
Terminal Signal
Screw
Size
Tightening Torque
Nm
(lb.in.)
Bare Cable Crimp Terminals
Wire Type
Applicable Gauges
mm
2
Recomm. Gauge
mm
2
Applicable Gauges
mm
2
Recomm. Gauge
mm
2
A+, A–, B+,
B–, Z+, Z–,
FE, IP, IG
M2
0.22 to 0.25
(1.95 to 2.21)
0.75
(18 AWG)
Stranded wire:
0.25 to 1.0
(24 to 17 AWG)
Solid wire:
0.25 to 1.5
(24 to 16 AWG)
0.5
(20 AWG)
0.25 to 0.5
(24 to 20 AWG)
Shielded twisted
pair, etc.
AO, IG, BO,
IG, ZO, IG
Shielded cable,
etc.
Wire Gauge
mm
2
Phoenix Contact Model
L
mm (in)
d1
mm (in)
d2
mm (in)
0.25 (24 AWG)
AI 0.25 - 6YE
AI 0.25 - 6BU
10.5 (13/32) 0.8 (1/32) 2 (5/64)
0.34 (22 AWG) AI 0.34 - 6TQ 10.5 (13/32) 0.8 (1/32) 2 (5/64)
0.5 (20 AWG) AI 0.5 - 6WH 12 (15/32) 1.1 (3/64) 2.5 (3/32)
Option Terminal
PG Encoder Cable
Wire Color Pin
IP 1 Blue C
IG 2 White H
A+ 3 Yellow B
A– 4 White G
B+ 5 Green A
B– 6 White F
FE E N/A (shield) D
d1
d2
6 mm
(0.24 in.)
L
A+ A- B+ B- Z+ Z- SD FE
IP IG AO IG BO IG ZO IG
A
B
C
D
E
F
G
H
TA1
TB1 TB2
Pin
3456 E 12
PG encoder side
B3
SIEP_C710616_38F_5_0.book 361 ージ 015年11月9日 月曜日 午後3時36分

Table of Contents

Other manuals for YASKAWA L1000A

Related product manuals