B.3 Parameter Table
YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual 435
U4-20
(7DCH)
Speed Reference From Option
Card
Displays the speed reference input by an option card (decimal).
No signal output
available
0.01%
<29>
–
U4-21
(7DDH)
Up/Down Command Source
Selection
Displays the source for the Up/Down command as XY-nn.
X: Indicates which Up/Down command source is used:
1 = Reference 1 (b1-02)
Y: Input power supply data
0 = Digital operator
1 = External terminals
3 = MEMOBUS/Modbus communications
4 = Communication option card
nn: Up/Down command limit status data
00: No limit status.
01: Up/Down command was left on when stopped in the PRG mode
02: Up/Down command was left on when switching from LOCAL to REMOTE operation
03: Waiting for soft charge bypass contactor after power up (Uv or Uv1 flashes after 10 s)
04: Waiting for “Up/Down Command Prohibited” time period to end
05: Fast Stop (multi-function input, operator)
07: During baseblock while coast to stop with timer
08: Speed reference is below minimal reference during baseblock
09: Waiting for Enter command
No signal output
available
––
U4-22
(7DEH)
MEMOBUS/Modbus
Communications Reference
Displays the drive control data set by MEMOBUS/Modbus communications register no. 0001H
as a four-digit hexadecimal number.
No signal output
available
––
U4-23
(7DFH)
Communication Option Card
Reference
Displays drive control data set by an option card as a four-digit hexadecimal number.
No signal output
available
––
U4-24
(7E6H)
Number of Travels
(Lower 4 digit)
Displays the lower four digits for the number of trips the drive has made.
No signal output
available
1 time
–
U4-25
(7E7H)
Number of Travels
(Higher 4 digit)
Displays the upper four digits for the number of trips the drive has made.
No signal output
available
1 time
–
U4-26
(7E8H)
Max. Current during
Acceleration
Shows the maximum current that occurred during acceleration.
No signal output
available
0.1 A –
U4-27
(7E9H)
Max. Current during
Deceleration
Shows the maximum current that occurred during deceleration.
No signal output
available
0.1 A –
U4-28
(7EAH)
Max. Current during Constant
Speed
Shows the maximum current that occurred during ride at top speed.
No signal output
available
0.1 A –
U4-29
(7EDH)
Max. Current during Leveling
Speed
Shows the maximum current that occurred during ride at leveling speed.
No signal output
available
0.1 A –
U4-30
(7EEH)
Slip Compensation Value
Shows the slip compensation value.
No signal output
ava
ilable
0.01% –
U4-31
(7EFH)
Ca
r Acceleration Rate
Shows the car acceleration rate.
No signal output
available
0.01 m/s
2
–
U4-40
(7FDH)
Speed Reference Limit at
Rescue Operation
Displays the speed limit for Rescue Operation based on how much power the backup battery or
UPS has. Displays 0% when Rescue Operation is not being performed.
No signal output
available
1% –
U4-42
(855H)
<35>
Remaining Distance
Displays the remaining distance according to the stopping method selected.
10 V:
S5-10 = 1: S5-11
S5-10 = 2: S5-12
1 mm –
U4-43
(856H)
<35>
Minimum Deceleration
Distance
Displays the Minimum Deceleration Distance calculated by E1-04.
No signal output
available
1 mm –
U4-44
(857H)
<35>
Minimum Stop Distance
Displays the Minimum Stop Distance calculated by d1-26.
No signal output
available
1 mm –
<29> Setting units are determined by the digital operator display unit selection (o1-03). When o1-03 = 0, the value is set in Hertz. When o1-03 = 4
or 5, the value is displayed in m/s. When o1-03 = 6, the value is displayed in ft/min.
<35> o1-12 (Length Units) determines the units. When o1-12 is set to 0, the unit is millimeters. When o1-12 is set to 1, the unit is inch.
<40> When checking the values of U1-03, U2-05 and U4-13 with the digital operator they are displayed in units of amperes, but when they are
checked using MEMOBUS communications, the monitor value in MEMOBUS communications is: displayed numeric value / 8192 × drive’s
rated current (A), from the condition “8192 (maximum value) = drive’s rated current (A)”.
<41> The MEMOBUS communications data is in 10 h units. If data in 1 h units are also required, refer to register number 0099H.
<42> The MEMOBUS communications data is in 10 h units. If data in 1 h units are also required, refer to register number 009BH.
No. (Addr.) Name Description
Analog Output
Level
Unit Page
All Modes
All Modes
All Modes
All Modes
All Modes
All Modes
All Modes
All Modes
All Modes
All Modes
CLV
CLV/PM
V/f OLV
CLV
CLV/PM
V/f OLV
All Modes
CLV
CLV/PM
V/f OLV
CLV
CLV/PM
V/f OLV
CLV
CLV/PM
V/f OLV
SIEP_C710616_38F_5_0.book 435 ページ ２０１５年１１月９日 月曜日 午後３時３６分
To Next Page
Loading...
