ABB SmartTouch i-bus KNX - Page 331

Index
Product manual 2CKA00xx73xxxxx
│
331
Setpoint adjustment — Maximum manual increase
during heating mode (0 - 9°C) ...................... 221
Setpoint adjustment — Maximum manual reduction
during cooling mode (0 - 9°C) ....................... 237
Setpoint adjustment — Maximum manual reduction
during heating mode (0 - 9°C) ...................... 222
Setpoint adjustment — Permanent storage of on-site
operation ......................................... 223, 238
Setpoint adjustment — Resetting of the manual
adjustment for receipt of a basic setpoint .. 222, 237
Setpoint adjustment — Resetting the manual
adjustment for change of operating mode .. 222, 237
Setpoint adjustment — Resetting the manual
adjustment via object .......................... 223, 238
Setpoint settings — Cyclic sending of the current set-
point temperature (min) ....................... 221, 236
Setpoint settings — Hysteresis for switchover
heating/cooling ........................................ 250
Setpoint settings — Increase for ECO cooling (°C) .. 235
Setpoint settings — Increase for standby cooling (°C)
........................................................... 235
Setpoint settings — Reduction for ECO heating (°C) 220
Setpoint settings — Reduction for standby heating (°C)
........................................................... 220
Setpoint settings — Send current setpoint ...... 221, 236
Setpoint settings — Setpoint for heating comfort =
setpoint for cooling comfort ........................ 249
Setpoint settings — Setpoint temperature for cooling
comfort (°C) ........................................... 235
Setpoint settings — Set-point temperature for frost
protection (°C) ........................................ 221
Setpoint settings — Set-point temperature for heat
protection (°C) ........................................ 236
Setpoint settings — Setpoint temperature for heating
and cooling comfort (°C)............................. 250
Setpoint settings — Setpoint temperature for heating
comfort (°C) ........................................... 220
Setting master/slave switches ..................... 38, 323
Setting options per channel .............................. 93
Setting up of video surveillance ........................ 294
Settings of basic load — Minimum control value for
basic load > 0 .................................... 219, 234
Special functions .......................................... 289
Specifying a name ......................................... 92
Specifying/editing buttons ......................... 96, 101
Specifying/editing functions ....................... 96, 101
Summer compensation ................................... 243
Summer compensation — (Lower) Starting temperature
for summer compensation (°C) ..................... 245
Summer compensation — Offset of the set-point
temperature for the entry into summer
compensation (x 0.1°C) .............................. 245
Summer compensation — Offset of the set-point
temperature for the exit from summer
compensation (x 0.1°C) .............................. 246
Summer compensation — Summer compensation ... 244
Switching light ............................................ 298
System Access Point ....................................... 90
System settings ........................................... 309
Access management.....................................................316
Display ..........................................................................311
Extended settings..........................................................320
Intercom list ...................................................................318
Network connections .....................................................314
Programming button......................................................320
Software update ............................................................321
Sound ............................................................................313
Time and date ...............................................................315
User settings .................................................................317
Via .................................................................................322
Video surveillance .........................................................317
T
Target group ................................................ 16
Technical data .............................................. 28
Temperature reading — Adjustment value for internal
temperature measurement (x 0.1°C) ........ 225, 241
Temperature reading — Control value for fault (0 -
255) ............................................... 226, 242
Temperature reading — Cyclic sending of actual
temperature (min) .............................. 224, 240
Temperature reading — Difference of value for sending
the actual temperature (x 0.1°C) ............ 225, 240
Temperature reading — Inputs of temperature reading
.................................................... 223, 238
Temperature reading — Inputs of weighted
temperature reading ........................... 223, 239
Temperature reading — Monitoring time for
temperature reading (0 = no monitoring) (min) 225,
242
Temperature reading — Operating mode for fault .. 250
Temperature reading — Weighting of external
measurement (0 to 100%) ..................... 224, 239
Temperature reading — Weighting of external
measurement 2 (0 to 100%) ................... 224, 240
Temperature reading — Weighting of internal
measurement (0 to 100%) ..................... 224, 239
Terminal resistor ......................................... 323
Time programs ...................................... 290, 306
Tools (functions) ........................................... 88
transfer of pid file (configuration file) ......... 320, 324
U
Update ............................................... 310, 324