ABB SmartTouch i-bus KNX

Table of contents
Product manual 2CKA00xx73xxxxx
│
9
10.20.8  Scene number ...........................................................................................................................196 
10.20.9  Light scenes can be started with ...............................................................................................196 
10.20.10  Light scene can be stored .........................................................................................................196 
10.20.11  Object x is to be changed ..........................................................................................................196 
10.21  Application "Presence simulation" ................................................................................................. 197 
10.21.1  Use of presence simulation .......................................................................................................197 
10.21.2  Page PIN-protected ...................................................................................................................197 
10.21.3  Enable export ............................................................................................................................197 
10.21.4  Delay time up to activation [min.] ...............................................................................................198 
10.21.5  Object type 1-20 ........................................................................................................................198 
10.22  Application "Time programs" .......................................................................................................... 199 
10.22.1  Page PIN-protected ...................................................................................................................199 
10.22.2  Overwriting time programs during download .............................................................................199 
10.23  Application "Logical functions" ....................................................................................................... 200 
10.23.1  Channel x — Application ...........................................................................................................200 
10.24  Application "Internal RTC" ............................................................................................................. 211 
10.24.1  General — Device function .......................................................................................................211 
10.24.2  General — Control function .......................................................................................................211 
10.24.3  General - Operating mode after reset ........................................................................................212 
10.24.4  General — Send cyclic "In operation" (min) ..............................................................................213 
10.24.5  General - Additional functions/objects .......................................................................................213 
10.24.6  General — Delay time for read telegrams after reset [s]............................................................213 
10.24.7  Heating control — Control value type ........................................................................................214 
10.24.8  Heating control — Heating type .................................................................................................215 
10.24.9  Heating control — P-component (x 0.1°C) ................................................................................215 
10.24.10  Heating control — I-component (min.) .......................................................................................216 
10.24.11  Heating control — Extended settings ........................................................................................216 
10.24.12  Basic stage heating ...................................................................................................................216 
10.24.13  Basic stage heating — Status object heating ............................................................................216 
10.24.14  Basic stage heating — Mode of the control value ......................................................................216 
10.24.15  Basic stage heating — Hysteresis (x 0.1°C) ..............................................................................217 
10.24.16  Basic stage heating — Control value difference for sending of heating control value ................217 
10.24.17  Basic stage heating — Cyclic sending of the control value (min)...............................................217 
10.24.18  Basic stage heating — PWM cycle heating (min) ......................................................................218 
10.24.19  Basic stage heating — Maximum control value (0 - 255) ...........................................................218 
10.24.20  Basic stage heating — Minimum control value for basic load (0 to 255) ....................................218 
10.24.21  Settings of basic load — Minimum control value for basic load > 0 ...........................................219 
10.24.22  Basic load settings — Basic load active when controller is off ...................................................219 
10.24.23  Setpoint settings — Setpoint temperature for heating comfort (°C) ...........................................220 
10.24.24  Setpoint settings — Reduction for standby heating (°C) ............................................................220 
10.24.25  Setpoint settings — Reduction for ECO heating (°C) ................................................................220 
10.24.26  Setpoint settings — Set-point temperature for frost protection (°C) ...........................................221 
10.24.27  Setpoint settings — Send current setpoint ................................................................................221 
10.24.28  Setpoint settings — Cyclic sending of the current set-point temperature (min) ..........................221 
10.24.29  Setpoint adjustment — Maximum manual increase during heating mode (0 - 9°C) ...................221 
10.24.30  Setpoint adjustment — Maximum manual reduction during heating mode (0 - 9°C) ..................222 
10.24.31  Setpoint adjustment — Resetting of the manual adjustment for receipt of a basic setpoint .......222 
10.24.32  Setpoint adjustment — Resetting the manual adjustment for change of operating mode ..........222 
10.24.33  Setpoint adjustment — Resetting the manual adjustment via object .........................................223 
10.24.34  Setpoint adjustment — Permanent storage of on-site operation ...............................................223 
10.24.35  Temperature reading — Inputs of temperature reading .............................................................223 