Calrec SIGMA - Page 148

174 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

148 S I G M A with Bluefin

Table of Contents

Default Chapter3
- Table of Contents3
- Important Information4
- Health and Safety5
- Technical Support6
Overview7
- Introduction8
- Principal Features9
- System Specification10
- Layering and Assignable Control11
- Paths and Ports12
- Signal Paths13
- Inputs and Outputs14
- Getting Started15
- Touch Screen Layout16
- Error Messages (AWACS)17
Fader Area19
- Channel and Group Faders20
- Channel Control21
- Assignable Fader22
- VCA Grouping23
- Automatic Cross-Fading24
- Layer Locking26
5.1 Surround27
- 5.1 Surround CHANNELS28
- Points to Remember31
Input and Output Controls33
- I/O Matrix34
- Input/Output Controls36
- Direct Output and MIX Minus37
- Stereo and Surround Panning38
- Motorized Joystick Panel39
- Delay40
Channel Functions41
- User-Chan Screen42
- EQ and Filters44
- Dynamics45
- Channel Copy46
- Broadcast Facilities47
- Console Functions48
Busses49
- Routing and Track Output Controls50
- Routing Matrix52
- Main Outputs53
- Busses Screen54
- Auxiliaries55
- Talkback56
- Oscillator Screen57
Memories59
- Memory Controls60
- Memory Set up Screen61
- Memory Isolation62
- Partial Memories63
Monitoring System65
- Assignable Monitoring & Metering66
- Monitor Panel Setup67
- Saving and Restoring Configurations68
- Misc Output and Meters69
- Control Room Misc Functions70
- Decoder Remotes71
Metering System73
- TFT Meters74
- TFT Meter Setup Screen75
- Adjusting TFT Screen Layout76
- Meter Configuration77
- TFT Configuration Examples78
- Saving and Restoring Configurations81
On-Screen Patching83
- Input Ports84
- Output Ports85
- Assignable Insert Sends86
- Assignable Insert Returns87
- Insert Screen88
- Main Insert Sends89
- Main Insert Returns90
- Monitoring, Talkback and Oscillator Outputs91
- Direct Output Ports92
- External Meter Output Ports92
- Input-Output Ports93
- Direct Input Ports93
- Input Usage Screen94
Port List Management95
- Port List Allocation96
- Port List Order97
- Sorting and Managing Port Lists98
- Saving and Restoring Lists99
- 44 Saving and Restoring Lists 99 Appendix C - Traditional Style101
Engineering Information101
- Tech Screen102
- Operational Modes103
- Miscellaneous Screen104
- Synchronization Screen105
- Talkback and Tone Inputs106
- External Monitor Inputs107
- External Meter Inputs108
- States Screen109
- Condition Switching110
- General Purpose Outputs Screen111
- General Purpose Inputs112
- Serial Interface113
- Router Label Setup Screen114
- Router Label Association Screen115
- Madi116
- PC Information117
- File Backup118
Hydra Audio Networking119
- Hydra Technology120
- Typical Hydra Network Example121
- Hydra I/O Boxes122
- Fixed Format Boxes123
- SDI Boxes125
- Modular Hydra I/O Boxes126
- Modular Hydra PSU127
- Modular I/O Box Configuration128
- Network Configuration129
- Hydra I/O Source Lists130
- Device Status131
- Patching Hydra Sources132
- Source Ownership133
- SDI Inputs134
Setup Application135
- Setup Application136
- Console Settings137
- Meters / Levels140
- Monitoring142
- Inputs and Outputs145
- Inserts146
- Main Line Mon147
Programming Utility149
- Programming Utility150
Appendix A - Offline Editor155
- Part 1 - on the Console PC156
- Part 2 - on the Laptop PC157
- Part 3 - on the Console PC160
Appendix B - Style 1 Faders161
- Channel and Group Faders (Style 1)162
Appendix C - Traditional Style Monitor Panel163
- Traditional Style Monitor Panel164
- Monitor Selector Set up166
- Monitor LS Set up167
- States Screen168
Appendix D - Version Changes169
- Version Changes170

Other manuals for Calrec SIGMA

Installation Manual98 pages