Calrec SIGMA - SIGMA PROGRAMMING UTILITY

174 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

calrec.com

SIGMA

Putting Sound in the Picture

PROGRAMMING UTILITy

Table of Contents

Default Chapter3
- Table of Contents3
- Important Information4
- Health and Safety5
- Technical Support6
Overview7
- Introduction8
- Principal Features9
- System Specification10
- Layering and Assignable Control11
- Paths and Ports12
- Signal Paths13
- Inputs and Outputs14
- Getting Started15
- Touch Screen Layout16
- Error Messages (AWACS)17
Fader Area19
- Channel and Group Faders20
- Channel Control21
- Assignable Fader22
- VCA Grouping23
- Automatic Cross-Fading24
- Layer Locking26
5.1 Surround27
- 5.1 Surround CHANNELS28
- Points to Remember31
Input and Output Controls33
- I/O Matrix34
- Input/Output Controls36
- Direct Output and MIX Minus37
- Stereo and Surround Panning38
- Motorized Joystick Panel39
- Delay40
Channel Functions41
- User-Chan Screen42
- EQ and Filters44
- Dynamics45
- Channel Copy46
- Broadcast Facilities47
- Console Functions48
Busses49
- Routing and Track Output Controls50
- Routing Matrix52
- Main Outputs53
- Busses Screen54
- Auxiliaries55
- Talkback56
- Oscillator Screen57
Memories59
- Memory Controls60
- Memory Set up Screen61
- Memory Isolation62
- Partial Memories63
Monitoring System65
- Assignable Monitoring & Metering66
- Monitor Panel Setup67
- Saving and Restoring Configurations68
- Misc Output and Meters69
- Control Room Misc Functions70
- Decoder Remotes71
Metering System73
- TFT Meters74
- TFT Meter Setup Screen75
- Adjusting TFT Screen Layout76
- Meter Configuration77
- TFT Configuration Examples78
- Saving and Restoring Configurations81
On-Screen Patching83
- Input Ports84
- Output Ports85
- Assignable Insert Sends86
- Assignable Insert Returns87
- Insert Screen88
- Main Insert Sends89
- Main Insert Returns90
- Monitoring, Talkback and Oscillator Outputs91
- Direct Output Ports92
- External Meter Output Ports92
- Input-Output Ports93
- Direct Input Ports93
- Input Usage Screen94
Port List Management95
- Port List Allocation96
- Port List Order97
- Sorting and Managing Port Lists98
- Saving and Restoring Lists99
- 44 Saving and Restoring Lists 99 Appendix C - Traditional Style101
Engineering Information101
- Tech Screen102
- Operational Modes103
- Miscellaneous Screen104
- Synchronization Screen105
- Talkback and Tone Inputs106
- External Monitor Inputs107
- External Meter Inputs108
- States Screen109
- Condition Switching110
- General Purpose Outputs Screen111
- General Purpose Inputs112
- Serial Interface113
- Router Label Setup Screen114
- Router Label Association Screen115
- Madi116
- PC Information117
- File Backup118
Hydra Audio Networking119
- Hydra Technology120
- Typical Hydra Network Example121
- Hydra I/O Boxes122
- Fixed Format Boxes123
- SDI Boxes125
- Modular Hydra I/O Boxes126
- Modular Hydra PSU127
- Modular I/O Box Configuration128
- Network Configuration129
- Hydra I/O Source Lists130
- Device Status131
- Patching Hydra Sources132
- Source Ownership133
- SDI Inputs134
Setup Application135
- Setup Application136
- Console Settings137
- Meters / Levels140
- Monitoring142
- Inputs and Outputs145
- Inserts146
- Main Line Mon147
Programming Utility149
- Programming Utility150
Appendix A - Offline Editor155
- Part 1 - on the Console PC156
- Part 2 - on the Laptop PC157
- Part 3 - on the Console PC160
Appendix B - Style 1 Faders161
- Channel and Group Faders (Style 1)162
Appendix C - Traditional Style Monitor Panel163
- Traditional Style Monitor Panel164
- Monitor Selector Set up166
- Monitor LS Set up167
- States Screen168
Appendix D - Version Changes169
- Version Changes170

Other manuals for Calrec SIGMA

Installation Manual98 pages