Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
100
Cisco TelePresence SX80 Administrator Guide
Cameras SpeakerTrack Mode
This setting applies only when using a Cisco TelePresence SpeakerTrack 60 camera.
The SpeakerTrack 60 camera assembly consists of two cameras and uses an audio tracking
technique that finds and captures a close-up of the active speaker. When a change of
speaker is detected, the system can switch automatically between the two cameras to
always show the best camera view. Refer to the Cameras SpeakerTrack TrackingMode
setting for different switching modes.
Requires user role: ADMIN, USER
Default value: Auto
Value space: Auto/Off
Auto: Speaker tracking is switched on. The cameras in the camera assembly behave
as one integrated unit that finds the active speaker and dynamically chooses the best
camera view.
Off: The cameras operate as two individual cameras. Speaker tracking is not used.
Cameras SpeakerTrack TrackingMode
This setting applies only when using a Cisco TelePresence SpeakerTrack 60 camera, and
when Cameras SpeakerTrack Mode is set to Auto.
The speaker tracking algorithm can react to changes in two modes, one faster than the
other. The mode determines when the camera view will change to a new speaker.
Requires user role: ADMIN, USER
Default value: Auto
Value space: Auto/Conservative
Auto: Normal tracking mode.
Conservative: The camera view will change to a new speaker later than in Normal mode.
Cameras SpeakerTrack ConnectorDetection Mode
This setting applies only when a Cisco TelePresence SpeakerTrack 60 camera is connected
to the codec (video system).
Define whether to automatically detect or manually configure which video input each
individual camera is connected to. You should choose manual configuration in situations
where the codec does not receive EDID information from the cameras. Typically, this will be
when you use HDMI repeaters that do not pass on EDID information.
Requires user role: ADMIN, USER
Default value: Auto
Value space: Auto/Manual
Auto: Automatically detect which video inputs the cameras are connected to.
Manual: Manually define which video inputs the cameras are connected to. Use the
Cameras SpeakerTrack ConnectorDetection CameraLeft and Cameras SpeakerTrack
ConnectorDetection CameraRight settings.
Cameras SpeakerTrack ConnectorDetection CameraLeft
This setting applies only when a Cisco TelePresence SpeakerTrack 60 camera is connected
to the codec (video system). Furthermore, Cameras SpeakerTrack ConnectorDetection
Mode must be set to Manual.
Define the number of the video input that SpeakerTrack 60's left camera is connected to.
Requires user role: ADMIN, USER
Default value: 1
Value space: Integer (1..5)
Set a valid video input number. For example, set to 1 if the left camera is connected to
video input 1.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g