Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
148
Cisco TelePresence SX80 Administrator Guide
UserManagement settings
UserManagement LDAP Mode
The video system supports the use of an LDAP (Lightweight Directory Access Protocol)
server as a central place to store and validate user names and passwords. Use this setting
to configure whether or not to use LDAP authentication. Our implementation is tested for
the Microsoft Active Directory (AD) service.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: LDAP authentication is not allowed.
On: Use LDAP authentication.
UserManagement LDAP Server Address
Set the IP address or hostname of the LDAP server.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 255)
A valid IPv4 address, IPv6 address or hostname.
UserManagement LDAP Server Port
Set the port to connect to the LDAP server on. If set to 0, use the default for the selected
protocol (see the UserManagement LDAP Encryption setting).
Requires user role: ADMIN
Default value: 0
Value space: Integer (0..65535)
The LDAP server port number.
UserManagement LDAP Encryption
Define how to secure the communication between the video system and the LDAP server.
You can override the port number by using the UserManagement LDAP Server Port setting.
Requires user role: ADMIN
Default value: LDAPS
Value space: LDAPS/None/STARTTLS
LDAPS: Connect to the LDAP server on port 636 over TLS (Transport Layer Security).
None: Connect to LDAP server on port 389 with no encryption.
STARTTLS: Connect to LDAP server on port 389, then send STARTTLS to enable TLS
encryption.
UserManagement LDAP MinimumTLSVersion
Set the lowest version of the TLS (Transport Layer Security) protocol that is allowed.
Requires user role: ADMIN
Default value: TLSv1.2
Value space: TLSv1.0/TLSv1.1/TLSv1.2
TLSv1.0: Support TLS version 1.0 or higher.
TLSv1.1: Support TLS version 1.1 or higher.
TLSv1.2: Support TLS version 1.2 or higher.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g