Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
116
Cisco TelePresence SX80 Administrator Guide
Network [1] IPv6 Assignment
Define how the system will obtain its IPv6 address and the default gateway address. This
setting only applies to systems on IPv6 networks.
Requires user role: ADMIN
Default value: Autoconf
Value space: Static/DHCPv6/Autoconf
Static: The codec and gateway IP addresses must be configured manually using the
Network IPv6 Address and Network IPv6 Gateway settings. The options, for example
NTP and DNS server addresses, must either be set manually or obtained from a DHCPv6
server. The Network IPv6 DHCPOptions setting determines which method to use.
DHCPv6: All IPv6 addresses, including options, will be obtained from a DHCPv6 server.
See RFC 3315 for a detailed description. The Network IPv6 DHCPOptions setting will be
ignored.
Autoconf: Enable IPv6 stateless autoconfiguration of the IPv6 network interface. See
RFC 4862 for a detailed description. The options, for example NTP and DNS server
addresses, must either be set manually or obtained from a DHCPv6 server. The Network
IPv6 DHCPOptions setting determines which method to use.
Network [1] IPv6 Address
Define the static IPv6 network address for the system. Applicable only when the Network
IPv6 Assignment is set to Static.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 64)
A valid IPv6 address including a network mask. Example: 2001:DB8::/48
Network [1] IPv6 Gateway
Define the IPv6 network gateway address. This setting is only applicable when the Network
IPv6 Assignment is set to Static.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 64)
A valid IPv6 address.
Network [1] IPv6 DHCPOptions
Retrieve a set of DHCP options, for example NTP and DNS server addresses, from a
DHCPv6 server.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: Disable the retrieval of DHCP options from a DHCPv6 server.
On: Enable the retrieval of a selected set of DHCP options from a DHCPv6 server.
Network [1] MTU
Define the Ethernet MTU (Maximum Transmission Unit) size. The MTU size must be
supported by your network infrastructure. The minimum size is 576 for IPv4 and 1280 for
IPv6.
Requires user role: ADMIN
Default value: 1500
Value space: Integer (576..1500)
Set a value for the MTU (bytes).
Network [1] QoS Mode
The QoS (Quality of Service) is a method which handles the priority of audio, video and
data in the network. The QoS settings must be supported by the infrastructure. Diffserv
(Differentiated Services) is a computer networking architecture that specifies a simple,
scalable and coarse-grained mechanism for classifying, managing network traffic and
providing QoS priorities on modern IP networks.
Requires user role: ADMIN
Default value: Diffserv
Value space: Off/Diffserv
Off: No QoS method is used.
Diffserv: When you set the QoS Mode to Diffserv, the Network QoS Diffserv Audio,
Network QoS Diffserv Video, Network QoS Diffserv Data, Network QoS Diffserv
Signalling, Network QoS Diffserv ICMPv6 and Network QoS Diffserv NTP settings are
used to prioritize packets.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g