Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
123
Cisco TelePresence SX80 Administrator Guide
NetworkServices SSH Mode
SSH (or Secure Shell) protocol can provide secure encrypted communication between the
codec and your local computer.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: The SSH protocol is disabled.
On: The SSH protocol is enabled.
NetworkServices SSH AllowPublicKey
Secure Shell (SSH) public key authentication can be used to access the codec.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: The SSH public key is not allowed.
On: The SSH public key is allowed.
NetworkServices Telnet Mode
Telnet is a network protocol used on the Internet or Local Area Network (LAN) connections.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: The Telnet protocol is disabled. This is the factory setting.
On: The Telnet protocol is enabled.
NetworkServices UPnP Mode
Fully disable UPnP (Universal Plug and Play), or enable UPnP for a short time period after
the video system has been switched on or restarted.
The default operation is that UPnP is enabled when you switch on or restart the video
system. Then UPnP is automatically disabled after the timeout period that is defined in the
NetworkServices UPnP Timeout setting.
When UPnP is enabled, the video system advertises its presence on the network. The
advertisement permits a Touch controller to discover video systems automatically, and
you do not need to manually enter the video system's IP address in order to pair the Touch
controller.
Requires user role: ADMIN
Default value: On
Value space: <Off/On>
Off: UPnP is disabled. The video system does not advertise its presence, and you have
to enter the video system's IP address manually in order to pair a Touch controller to the
video system.
On: UPnP is enabled. The video system advertises its presence until the timeout period
expires.
NetworkServices UPnP Timeout
Define for how many seconds UPnP shall stay enabled after the video system is switched
on or restarted. The NetworkServices UPnP Mode setting must be On for this setting to
take any effect.
Requires user role: ADMIN
Default value: 600
Value space: <0..3600>
Range: Select a value between 0 and 3600 seconds.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g