Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
103
Cisco TelePresence SX80 Administrator Guide
Conference DefaultCall Protocol
Define the Default Call Protocol to be used when placing calls from the system.
Requires user role: ADMIN
Default value: Auto
Value space: Auto/H320/H323/Sip/Spark
Auto: Enables auto-selection of the call protocol based on which protocols are available.
If multiple protocols are available, the order of priority is: 1) SIP; 2) H323; 3) H320. If the
system cannot register, the auto-selection chooses H323.
H320: All calls are set up as H.320 calls (only applicable if connected to Cisco
TelePresence ISDN Link).
H323: All calls are set up as H.323 calls.
Sip: All calls are set up as SIP calls.
Spark: Reserved for Spark registered systems. Do not use.
Conference DefaultCall Rate
Define the Default Call Rate to be used when placing calls from the system.
Requires user role: ADMIN
Default value: 3072
Value space: Integer (64..6000)
The default call rate (kbps).
Conference DoNotDisturb DefaultTimeout
This setting determines the default duration of a Do Not Disturb session, i.e. the period
when incoming calls are rejected and registered as missed calls. The session can be
terminated earlier by using the user interface. The default value is 60 minutes.
Requires user role: ADMIN
Default value: 60
Value space: Integer (1..1440)
The number of minutes (maximum 1440 minutes = 24 hours) before the Do Not Disturb
session times out automatically.
Conference Encryption Mode
Define the conference encryption mode. A padlock with the text "Encryption On" or
"Encryption Off" displays on screen for a few seconds when the conference starts.
NOTE: If the Encryption Option Key is not installed on the video system, the encryption
mode is always Off.
Requires user role: ADMIN
Default value: BestEffort
Value space: Off/On/BestEffort
Off: The system will not use encryption.
On: The system will only allow calls that are encrypted.
BestEffort: The system will use encryption whenever possible.
> In Point to point calls: If the far end system supports encryption (AES-128), the call will
be encrypted. If not, the call will proceed without encryption.
> In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must
support encryption. If not, the conference will be unencrypted.
Conference FarEndControl Mode
Lets you decide if the remote side (far end) should be allowed to select your video sources
and control your local camera (pan, tilt, zoom).
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: The far end is not allowed to select your video sources or to control your local
camera (pan, tilt, zoom).
On: Allows the far end to be able to select your video sources and control your local
camera (pan, tilt, zoom). You will still be able to control your camera and select your
video sources as normal.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g