Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
150
Cisco TelePresence SX80 Administrator Guide
Video settings
Video ActiveSpeaker DefaultPIPPosition
Define the position on screen of the active speaker picture-in-picture (PiP). The setting only
takes effect when using a video layout where the active speaker is a PiP, i.e. the Overlay
layout, or possibly a Custom layout (refer to the Video DefaultLayoutFamily Local setting).
The setting takes effect from the next call onwards; if changed during a call, it will have no
effect on the current call.
Requires user role: ADMIN
Default value: Current
Value space: Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/
LowerLeft/LowerRight
Current: The position of the active speaker PiP will be kept unchanged when leaving a
call.
UpperLeft: The active speaker PiP will appear in the upper left corner of the screen.
UpperCenter: The active speaker PiP will appear in the upper center position.
UpperRight: The active speaker PiP will appear in the upper right corner of the screen.
CenterLeft: The active speaker PiP will appear in the center left position.
CentreRight: The active speaker PiP will appear in the center right position.
LowerLeft: The active speaker PiP will appear in the lower left corner of the screen.
LowerRight: The active speaker PiP will appear in the lower right corner of the screen.
Video DefaultLayoutFamily Local
Select which video layout family to use locally.
Requires user role: ADMIN
Default value: Auto
Value space: Auto/Equal/Prominent/Overlay/Single>
Auto: The default layout family, as given in the layout database provided by the system,
will be used as the local layout.
Equal: The Equal layout family will be used as the local layout. All videos have equal size,
as long as there is space enough on the screen.
Prominent: The Prominent layout family will be used as the local layout. The active
speaker, or the presentation if present, will be a large picture, while the other participants
will be small pictures. Transitions between active speakers are voice switched.
Overlay: The Overlay layout family will be used as the local layout. The active speaker,
or the presentation if present, will be shown in full screen, while the other participants
will be small pictures-in-picture (PiP). Transitions between active speakers are voice
switched.
Single: The active speaker, or the presentation if present, will be shown in full screen.
The other participants are not shown. Transitions between active speakers are voice
switched.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g