Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
134
Cisco TelePresence SX80 Administrator Guide
Security settings
Security Audit Logging Mode
Define where to record or transmit the audit logs. The audit logs are sent to a syslog server.
When using the External/ExternalSecure modes and setting the port assignment to manual
in the Security Audit Server PortAssignment setting, you must also enter the address and
port number for the audit server in the Security Audit Server Address and Security Audit
Server Port settings.
Requires user role: AUDIT
Default value: Off
Value space: Off/Internal/External/ExternalSecure
Off: No audit logging is performed.
Internal: The system records the audit logs to internal logs, and rotates logs when they
are full.
External: The system sends the audit logs to an external syslog server. The syslog server
must support UDP.
ExternalSecure: The system sends encrypted audit logs to an external syslog server that
is verified by a certificate in the Audit CA list. The Audit CA list file must be uploaded to
the codec using the web interface. The common_name parameter of a certificate in the
CA list must match the IP address of the syslog server, and the secure TCP server must
be set up to listen for secure (TLS) TCP Syslog messages.
Security Audit OnError Action
Define what happens when the connection to the syslog server is lost. This setting is only
relevant when Security Audit Logging Mode is set to ExternalSecure.
Requires user role: AUDIT
Default value: Ignore
Value space: Halt/Ignore
Halt: If a halt condition is detected the system codec is rebooted and only the auditor is
allowed to operate the unit until the halt condition has passed. When the halt condition
has passed the audit logs are re-spooled to the syslog server. Halt conditions are: A
network breach (no physical link), no syslog server running (or incorrect address or port
to the syslog server), TLS authentication failed (if in use), local backup (re-spooling) log
full.
Ignore: The system will continue its normal operation, and rotate internal logs when full.
When the connection is restored it will again send its audit logs to the syslog server.
Security Audit Server Address
The audit logs are sent to a syslog server. Define the IP address of the syslog server.
Only valid IPv4 or IPv6 address formats are accepted. Host names are not supported.
This setting is only relevant when Security Audit Logging Mode is set to External or
ExternalSecure.
Requires user role: AUDIT
Default value: ""
Value space: String (0, 255)
A valid IPv4 address or IPv6 address
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g