Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
113
Cisco TelePresence SX80 Administrator Guide
Network settings
Network [1] DNS Domain Name
The DNS Domain Name is the default domain name suffix which is added to unqualified
names.
Example: If the DNS Domain Name is "company.com" and the name to lookup is
"MyVideoSystem", this will result in the DNS lookup "MyVideoSystem.company.com".
Requires user role: ADMIN
Default value: ""
Value space: String (0, 64)
The DNS domain name.
Network [1] DNS Server [1..3] Address
Define the network addresses for DNS servers. Up to three addresses may be specified.
If the network addresses are unknown, contact your administrator or Internet Service
Provider.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 64)
A valid IPv4 address or IPv6 address.
Network [1] IEEE8021X Mode
The system can be connected to an IEEE 802.1X LAN network, with a port-based network
access control that is used to provide authenticated network access for Ethernet networks.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: The 802.1X authentication is disabled (default).
On: The 802.1X authentication is enabled.
Network [1] IEEE8021X TlsVerify
Verification of the server-side certificate of an IEEE802.1x connection against the
certificates in the local CA-list when TLS is used. The CA-list must be uploaded to the
video system. This can be done from the web interface.
This setting takes effect only when Network [1] IEEE8021X Eap Tls is enabled (On).
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: When set to Off, TLS connections are allowed without verifying the server-side
X.509 certificate against the local CA-list. This should typically be selected if no CA-list
has been uploaded to the codec.
On: When set to On, the server-side X.509 certificate will be validated against the local
CA-list for all TLS connections. Only servers with a valid certificate will be allowed.
Network [1] IEEE8021X UseClientCertificate
Authentication using a private key/certificate pair during an IEEE802.1x connection. The
authentication X.509 certificate must be uploaded to the video system. This can be done
from the web interface.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: When set to Off client-side authentication is not used (only server-side).
On: When set to On the client (video system) will perform a mutual authentication TLS
handshake with the server.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g