Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
115
Cisco TelePresence SX80 Administrator Guide
Network [1] IEEE8021X Eap Peap
Define the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN
clients without the need for client certificates. Developed by Microsoft, Cisco and RSA
Security.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: The EAP-PEAP protocol is disabled.
On: The EAP-PEAP protocol is enabled (default).
Network [1] IPStack
Select if the system should use IPv4, IPv6, or dual IP stack, on the network interface. NOTE:
After changing this setting you may have to wait up to 30 seconds before it takes effect.
Requires user role: ADMIN
Default value: Dual
Value space: Dual/IPv4/IPv6
Dual: When set to Dual, the network interface can operate on both IP versions at the
same time, and can have both an IPv4 and an IPv6 address at the same time.
IPv4: When set to IPv4, the system will use IPv4 on the network interface.
IPv6: When set to IPv6, the system will use IPv6 on the network interface.
Network [1] IPv4 Assignment
Define how the system will obtain its IPv4 address, subnet mask and gateway address. This
setting only applies to systems on IPv4 networks.
Requires user role: ADMIN
Default value: DHCP
Value space: Static/DHCP
Static: The addresses must be configured manually using the Network IPv4 Address,
Network IPv4 Gateway and Network IPv4 SubnetMask settings (static addresses).
DHCP: The system addresses are automatically assigned by the DHCP server.
Network [1] IPv4 Address
Define the static IPv4 network address for the system. Applicable only when Network IPv4
Assignment is set to Static.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 64)
A valid IPv4 address.
Network [1] IPv4 Gateway
Define the IPv4 network gateway address. Applicable only when the Network IPv4
Assignment is set to Static.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 64)
A valid IPv4 address.
Network [1] IPv4 SubnetMask
Define the IPv4 network subnet mask. Applicable only when the Network IPv4 Assignment
is set to Static.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 64)
A valid IPv4 address.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g