D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
157
Cisco TelePresence SX80 Administrator Guide
Video Output Connector [1..3] Location VerticalOffset
HorizontalOffset and VerticalOffset settings are associated with each video output. These
settings are used to signal the relative position of the displays that are connected to these
outputs.
HorizontalOffset = 0 and VerticalOffset = 0 indicates that the display is positioned in center,
both horizontally and vertically. A negative horizontal offset indicates that the monitor is
left of center, and a positive horizontal offset indicates that the monitor is right of center.
A negative vertical offset indicates that the monitor is below center, and a positive vertical
offset indicates that the monitor is above center. The magnitude of the offset indicates how
far the display is from center (relative to other displays).
Example: You have three displays side by side, with the left and right displays at equal
distance from center. Then the following settings will apply: HorizontalOffset = 0 for the
center display, HorizontalOffset = -1 for the left display, and HorizontalOffset = 1 for the
right display.
Example: You have two displays, one in center and one below. Then the following settings
will apply: VerticalOffset = 0 for the center display, Vertical Offset = -1 for the lower display.
The default values for the different outputs are:
Video Output Connector [1] Location: HorizontalOffset = -1, VerticalOffset = 0
Video Output Connector [2] Location: HorizontalOffset = 0, VerticalOffset = 0
Video Output Connector [3] Location: HorizontalOffset = 1, VerticalOffset = 0
Requires user role: ADMIN
Default value: 0
Value space: Integer (-100..100)
Range: The value must be between -100 and 100.
Video Output Connector [1..3] MonitorRole
The monitor role describes which video streams will be shown on the monitor connected
to this video output connector. Together the Video Monitors setting and the MonitorRole
settings for all outputs define which layout (video streams) will be shown on each monitor.
Requires user role: ADMIN
Default value: Auto
Value space: Auto/First/Second/PresentationOnly/Third/Recorder
Auto: The system will detect when a monitor is connected, and a monitor role (First,
Second, Third) that corresponds with the Video Monitors setting will be assigned
automatically.
First/Second/Third: Define the role of the monitor in a multi-monitor setup. In a single-
monitor setup, there is no difference between First, Second and Third.
PresentationOnly: Show presentation video stream if active, and nothing else. Monitors/
outputs with this monitor role are disregarded by the Video Monitors setting.
Recorder: Show all participants, including the local main video (self-view). If active, also
show the presentation. Monitors/outputs with this monitor role are disregarded by the
Video Monitors setting.
Video Output Connector [1..3] Resolution
Define the resolution and refresh rate for the connected screen.
Requires user role: ADMIN, USER
Default value: Auto
Value space: Auto/1280_720_50/1280_720_60/1920_1080_50/1920_1080_60/1920_120
0_50/1920_1200_60
Auto: The system will automatically try to set the optimal resolution based on negotiation
with the connected monitor.
1280_720_50: The resolution is 1280 x 720, and the refresh rate is 50 Hz.
1280_720_60: The resolution is 1280 x 720, and the refresh rate is 60 Hz.
1920_1080_50: The resolution is 1920 x 1080, and the refresh rate is 50 Hz.
1920_1080_60: The resolution is 1920 x 1080, and the refresh rate is 60 Hz.
1920_1200_50: The resolution is 1920 x 1200, and the refresh rate is 50 Hz.
1920_1200_60: The resolution is 1920 x 1200, and the refresh rate is 60 Hz.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
