Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
114
Cisco TelePresence SX80 Administrator Guide
Network [1] IEEE8021X Identity
Define the user name for 802.1X authentication.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 64)
The user name for 802.1X authentication.
Network [1] IEEE8021X Password
Define the password for 802.1X authentication.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 32)
The password for 802.1X authentication.
Network [1] IEEE8021X AnonymousIdentity
The 802.1X Anonymous ID string is to be used as unencrypted identity with EAP (Extensible
Authentication Protocol) types that support different tunneled identity, like EAP-PEAP and
EAP-TTLS. If set, the anonymous ID will be used for the initial (unencrypted) EAP Identity
Request.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 64)
The 802.1X Anonymous ID string.
Network [1] IEEE8021X Eap Md5
Define the Md5 (Message-Digest Algorithm 5) mode. This is a Challenge Handshake
Authentication Protocol that relies on a shared secret. Md5 is a Weak security.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: The EAP-MD5 protocol is disabled.
On: The EAP-MD5 protocol is enabled (default).
Network [1] IEEE8021X Eap Ttls
Define the TTLS (Tunneled Transport Layer Security) mode. Authenticates LAN clients
without the need for client certificates. Developed by Funk Software and Certicom. Usually
supported by Agere Systems, Proxim and Avaya.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: The EAP-TTLS protocol is disabled.
On: The EAP-TTLS protocol is enabled (default).
Network [1] IEEE8021X Eap Tls
Enable or disable the use of EAP-TLS (Transport Layer Security) for IEEE802.1x
connections. The EAP-TLS protocol, defined in RFC 5216, is considered one of the most
secure EAP standards. LAN clients are authenticated using client certificates.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: The EAP-TLS protocol is disabled.
On: The EAP-TLS protocol is enabled (default).
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g