Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
122
Cisco TelePresence SX80 Administrator Guide
NetworkServices SNMP Mode
SNMP (Simple Network Management Protocol) is used in network management systems
to monitor network-attached devices (routers, servers, switches, projectors, etc) for
conditions that warrant administrative attention. SNMP exposes management data in the
form of variables on the managed systems, which describe the system configuration. These
variables can then be queried (set to ReadOnly) and sometimes set (set to ReadWrite) by
managing applications.
Requires user role: ADMIN
Default value: ReadOnly
Value space: Off/ReadOnly/ReadWrite
Off: Disable the SNMP network service.
ReadOnly: Enable the SNMP network service for queries only.
ReadWrite: Enable the SNMP network service for both queries and commands.
NetworkServices SNMP Host [1..3] Address
Define the address of up to three SNMP Managers.
The system's SNMP Agent (in the codec) responds to requests from SNMP Managers (a PC
program etc.), for example about system location and system contact. SNMP traps are not
supported.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 255)
A valid IPv4 address, IPv6 address or DNS name.
NetworkServices SNMP CommunityName
Define the name of the Network Services SNMP Community. SNMP Community names
are used to authenticate SNMP requests. SNMP requests must have a password (case
sensitive) in order to receive a response from the SNMP Agent in the codec. The default
password is "public". If you have the Cisco TelePresence Management Suite (TMS) you
must make sure the same SNMP Community is configured there too. NOTE: The SNMP
Community password is case sensitive.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 50)
The SNMP community name.
NetworkServices SNMP SystemContact
Define the name of the Network Services SNMP System Contact.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 50)
The name of the SNMP system contact.
NetworkServices SNMP SystemLocation
Define the name of the Network Services SNMP System Location.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 50)
The name of the SNMP system location.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g