Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
121
Cisco TelePresence SX80 Administrator Guide
NetworkServices HTTPS VerifyClientCertificate
When the video system connects to a HTTPS client (like a web browser), the client can be
asked to present a certificate to the video system to identify itself.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: Do not verify client certificates.
On: Requires the client to present a certificate that is signed by a trusted Certificate
Authority (CA). This requires that a list of trusted CAs are uploaded to the system in
advance.
NetworkServices HTTPS OCSP Mode
Define the support for OCSP (Online Certificate Status Protocol) responder services. The
OCSP feature allows users to enable OCSP instead of certificate revocation lists (CRLs) to
check the certificate status.
For any outgoing HTTPS connection, the OCSP responder is queried of the status. If the
corresponding certificate has been revoked, then the HTTPS connection will not be used.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: Disable OCSP support.
On: Enable OCSP support.
NetworkServices HTTPS OCSP URL
Define the URL of the OCSP responder (server) that will be used to check the certificate
status.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 255)
A valid URL.
NetworkServices NTP Mode
The Network Time Protocol (NTP) is used to synchronize the system's time and date to a
reference time server. The time server will be queried regularly for time updates.
Requires user role: ADMIN
Default value: Auto
Value space: Auto/Manual/Off
Auto: The system will use an NTP server for time reference. As default, the server
address will be obtained from the network's DHCP server. If a DHCP server is not used,
or if the DHCP server does not provide an NTP server address, the NTP server address
that is specified in the NetworkServices NTP Server [n] Address setting will be used.
Manual: The system will use the NTP server that is specified in the NetworkServices
NTP Server [n] Address setting for time reference.
Off: The system will not use an NTP server. The NetworkServices NTP Server [n]
Address setting will be ignored.
NetworkServices NTP Server [1..3] Address
The address of the NTP server that will be used when NetworkServices NTP Mode is set to
Manual, and when NetworkServices NTP Mode is set to Auto and no address is supplied by
a DHCP server.
Requires user role: ADMIN
Default value: 0.tandberg.pool.ntp.org
Value space: String (0, 255)
A valid IPv4 address, IPv6 address or DNS name.
NetworkServices SIP Mode
Define whether the system should be able to place and receive SIP calls or not.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: Disable the possibility to place and receive SIP calls.
On: Enable the possibility to place and receive SIP calls (default).
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g