Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
93
Cisco TelePresence SX80 Administrator Guide
Audio Output HDMI [1..2] Mode
Define if the audio channel on the HDMI output connector shall be enabled.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: Disable the audio channel on the HDMI output.
On: Enable the audio channel on the HDMI output.
Audio Output Line [1..6] Channel
Define whether the Audio Line output is a mono signal or part of a multichannel signal.
Requires user role: ADMIN
Default value: Left
Value space: Left/Mono/Right
Left: The Audio Line output signal is the left channel of a stereo signal.
Mono: The Audio Line output signal is a mono signal.
Right: The Audio Line output signal is the right channel of a stereo signal.
Audio Output Line [1..6] Delay DelayMs
To obtain lip-synchronization, you can configure each audio line output with an extra delay
that compensates for delay in other connected devices, for example TVs and external
loudspeakers. The delay that you set here is either fixed or relative to the delay on the HDMI
output, as defined in the Audio Output Line [n] Delay Mode setting.
Requires user role: ADMIN
Default value: 0
Value space: Integer (0..290)
The delay in milliseconds.
Audio Output Line [1..6] Delay Mode
You may add extra delay to an audio line output with the Audio Output Line [n] Delay
DelayMs setting. The extra delay added is either a fixed number of milliseconds, or
a number of milliseconds relative to the detected delay on the HDMI output (typically
introduced by the connected TV).
Requires user role: ADMIN
Default value: Fixed
Value space: Fixed/RelativeToHDMI
Fixed: Any extra delay (DelayMs) added to the output, will be a fixed number of
millisecond.
RelativeToHDMI: Any extra delay (DelayMs) added to the output, will be relative to the
detected delay on the HDMI output. The actual delay is HDMI-delay + DelayMs. The
Audio Output Connectors Line [n] DelayMs status reports the actual delay.
Audio Output Line [1..6] Equalizer ID
Select the equalizer ID for the audio source that is connected to the output line.
Requires user role: ADMIN
Default value: 1
Value space: Integer (1..8)
Set the equalizer ID.
Audio Output Line [1..6] Equalizer Mode
Define the equalizer mode for the audio source that is connected to the output line.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: No equalizer.
On: Enable the equalizer for the audio output line.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g