Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
99
Cisco TelePresence SX80 Administrator Guide
Cameras PresenterTrack Connector
This setting applies only when using a Cisco TelePresence SX80 with Precision 60 camera
or SpeakerTrack 60 camera.
Define which video input connector the presenter tracking camera is connected to.
Requires user role: ADMIN, USER
Default value: 1
Value space: Integer (1..5)
The video input connector.
Cameras PresenterTrack Enabled
This setting applies only when using a Cisco TelePresence SX80 with Precision 60 camera
or SpeakerTrack 60 camera.
Define whether or not the PresenterTrack feature is available for use.
Requires user role: ADMIN, USER
Default value: False
Value space: False/True
False: The PresenterTrack feature is disabled.
True: The PresenterTrack feature is available for use.
Cameras PresenterTrack PresenterDetectedStatus
This setting applies only when using a Cisco TelePresence SX80 with Precision 60 camera
or SpeakerTrack 60 camera.
Define whether or not to update the Cameras PresenterTrack PresenterDetected status
when a new person enters the trigger zone.
The status is is used by the codec's internal scripts in the Briefing room scenario. This
setting may be used to turn off automatic layout switching in that scenario.
Requires user role: ADMIN, USER
Default value: Enabled
Value space: Disabled/Enabled
Disabled: The status is not updated when a new person enters the trigger zone.
Enabled: The status is updated when a new person enters the trigger zone.
Cameras PresenterTrack TriggerZone
This setting applies only when using a Cisco TelePresence SX80 with Precision 60 camera
or SpeakerTrack 60 camera.
Define the image coordinates of the trigger zone on the video system screen. A person's
head must have been inside this region of the image in order to be tracked.
The format is a string of x and y coordinate pairs: "x1,y1,...xn,yn", where the range of x is
(0,1920) and y is (0,1080). Two coordinate pairs define the upper left and lower right corner
of a rectangular trigger zone. More than two coordinate pairs define the vertices of a
polygonal trigger zone.
Requires user role: ADMIN, USER
Default value: ""
Value space: String (0..255)
The coordinates for the trigger zone.
Cameras Preset TriggerAutofocus
The current position (pan and tilt), zoom and focus are stored with a preset. Use this setting
to determine if the camera should refocus or use the focus value that is stored with the
preset.
Requires user role: ADMIN
Default value: Auto
Value space: Auto/Off/On
Auto: Whether the camera refocuses or not when selecting a preset, depends on the
camera type.
Off: The focus value that is stored with the preset will be used. The camera will not
refocus when selecting a preset.
On: The camera will refocus when selecting a preset. The focus value that is stored with
the preset may be overridden.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g