Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
104
Cisco TelePresence SX80 Administrator Guide
Conference FarEndControl SignalCapability
Define the far end control (H.224) signal capability mode.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: Disable the far end control signal capability.
On: Enable the far end control signal capability.
Conference MaxReceiveCallRate
Define the maximum receive bit rate to be used when placing or receiving calls.
Note that this is the maximum bit rate for each individual call; use the Conference
MaxTotalReceiveCallRate setting to set the aggregated maximum for all simultaneous active
calls.
Requires user role: ADMIN
Default value: 6000
Value space: Integer (64..6000)
The maximum receive call rate (kbps).
Conference MaxTransmitCallRate
Define the maximum transmit bit rate to be used when placing or receiving calls.
Note that this is the maximum bit rate for each individual call; use the Conference
MaxTotalTransmitCallRate setting to set the aggregated maximum for all simultaneous active
calls.
Requires user role: ADMIN
Default value: 6000
Value space: Integer (64..6000)
The maximum transmitt call rate (kbps).
Conference MaxTotalReceiveCallRate
This configuration applies when using a video system's built-in MultiSite feature (optional) to
host a multipoint video conference.
Define the maximum overall receive bit rate allowed. The bit rate will be divided fairly among
all active calls at any time. This means that the individual calls will be up-speeded or down-
speeded as appropriate when someone leaves or enters a multipoint conference, or when a
call is put on hold (suspended) or resumed.
The maximum receive bit rate for each individual call is defined in the Conference
MaxReceiveCallRate setting.
Requires user role: ADMIN
Default value: 6000
Value space: Integer (64..6000)
The maximum receive call rate (kbps).
Conference MaxTotalTransmitCallRate
This configuration applies when using a video system's built-in MultiSite feature (optional) to
host a multipoint video conference.
Define the maximum overall transmit bit rate allowed. The bit rate will be divided fairly
among all active calls at any time. This means that the individual calls will be up-speeded or
down-speeded as appropriate when someone leaves or enters a multipoint conference, or
when a call is put on hold (suspended) or resumed.
The maximum transmit bit rate for each individual call is defined in the Conference
MaxTransmitCallRate setting.
Requires user role: ADMIN
Default value: 6000
Value space: Integer (64..6000)
The maximum transmit call rate (kbps).
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g