Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
89
Cisco TelePresence SX80 Administrator Guide
Audio MicrophoneReinforcement Gain
The gain (in dB) that will be applied to the mixed microphone signal that is fed to the
selected MicrophoneReinforcement outputs.
Requires user role: ADMIN
Default value: -54
Value space: Integer (-54..15)
Use this gain to adjust the level of microphone signal that should be fed to the local
output. The value -54 means "Off", and no signal will be fed from the microphone to the
output.
Audio SoundsAndAlerts RingTone
Define which ringtone to use for incoming calls.
Requires user role: ADMIN, USER
Default value: Sunrise
Value space: Sunrise/Mischief/Ripples/Reflections/Vibes/Delight/Evolve/Playful/Ascent/
Calculation/Mellow/Ringer
Select a ringtone from the list.
Audio SoundsAndAlerts RingVolume
Define the ring volume for incoming calls.
Requires user role: ADMIN, USER
Default value: 50
Value space: Integer (0..100)
The value goes in steps of 5 from 0 to 100 (from -34.5 dB to 15 dB). Volume 0 = Off.
Audio Input HDMI [1..3] Level
Define the audio level of the HDMI input connector.
Requires user role: ADMIN
Default value: 0
Value space: Integer (-24..0)
Select a value between -24 and 0, in steps of 1 dB.
Audio Input HDMI [1..3] Mode
Define if the audio channels on the HDMI input shall be enabled. The HDMI inputs have two
audio channels.
Requires user role: ADMIN
Default value: HDMI [1..2]: Off HDMI [3]: On
Value space: Off/On
Off: Disable audio on the HDMI input.
On: Enable audio on the HDMI input.
Audio Input HDMI [1..3] VideoAssociation MuteOnInactiveVideo
Determine whether to play audio only when you present the HDMI input source, or to always
play audio when an audio source is connected to the HDMI input.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: Audio is always played, locally and to far end; you do not have to present the HDMI
input source.
On: Audio is played, locally and to far end, only when you present the HDMI input source.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g