Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
139
Cisco TelePresence SX80 Administrator Guide
SIP PreferredIPMedia
Define the preferred IP version for sending and receiving media (audio, video, data). Only
applicable when both Network IPStack and Conference CallProtocolIPStack are set to Dual,
and the network does not have a mechanism for choosing the preferred IP version.
Requires user role: ADMIN
Default value: IPv4
Value space: IPv4/IPv6
IPv4: The preferred IP version for media is IPv4.
IPv6: The preferred IP version for media is IPv6.
SIP PreferredIPSignaling
Define the preferred IP version for signaling (audio, video, data). Only applicable when both
Network IPStack and Conference CallProtocolIPStack are set to Dual, and the network does
not have a mechanism for choosing the preferred IP version. It also determines the priority
of the A/AAAA lookups in DNS, so that the preferred IP version is used for registration.
Requires user role: ADMIN
Default value: IPv4
Value space: IPv4/IPv6
IPv4: The preferred IP version for signaling is IPv4.
IPv6: The preferred IP version for signaling is IPv6.
SIP Proxy [1..4] Address
The Proxy Address is the manually configured address for the outbound proxy. It is possible
to use a fully qualified domain name, or an IP address. The default port is 5060 for TCP and
UDP but another one can be provided.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 255)
A valid IPv4 address, IPv6 address or DNS name.
SIP TlsVerify
For TLS connections a SIP CA-list can be uploaded to the video system. This can be done
from the web interface.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: Set to Off to allow TLS connections without verifying them. The TLS connections
are allowed to be set up without verifying the x.509 certificate received from the server
against the local CA-list. This should typically be selected if no SIP CA-list has been
uploaded.
On: Set to On to verify TLS connections. Only TLS connections to servers, whose x.509
certificate is validated against the CA-list, will be allowed.
SIP Turn DiscoverMode
Define the discover mode to enable/disable the application to search for available Turn
servers in DNS. Before making calls, the system will test if port allocation is possible.
Requires user role: ADMIN
Default value: On
Value space: Off/On
Off: Set to Off to disable discovery mode.
On: When set to On, the system will search for available Turn servers in DNS, and before
making calls the system will test if port allocation is possible.
SIP Turn DropRflx
DropRflx will make the endpoint force media through the Turn relay, unless the remote
endpoint is on the same network.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: Disable DropRflx.
On: The system will force media through the Turn relay when the remote endpoint is on
another network.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g