Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
154
Cisco TelePresence SX80 Administrator Guide
High: Requires nearly optimal video conferencing lighting conditions and a good quality
video input in order to achieve a good overall experience. Rather high resolutions will be
used.
Video Input Connector [1..5] OptimalDefinition Threshold60fps
For each video input, this setting tells the system the lowest resolution where it should
transmit 60fps. So for all resolutions lower than this, the maximum transmitted frame rate
would be 30fps, while above this resolution 60fps would also be possible, if the available
bandwidth is adequate.
Requires user role: ADMIN
Default value: 1280_720
Value space: 512_288/768_448/1024_576/1280_720/1920_1080/Never
512_288: Set the threshold to 512x288.
768_448: Set the threshold to 768x448.
1024_576: Set the threshold to 1024x576.
1280_720: Set the threshold to 1280x720.
1920_1080: Set the threshold to 1920x1080.
Never: Do not set a threshold for transmitting 60fps.
Video Input Connector [1..4] PresentationSelection
Define how the video system will behave when you connect a presentation source to the
video input. In general, any input source can be used as a presentation source; normally,
the main camera will not be used as a presentation source.
If the video system is in standby mode, it will wake up when you connect a presentation
source. Sharing the presentation with the far end requires additional action (select Share on
the user interface) except when this setting is set to AutoShare.
Requires user role: ADMIN
Default value: Connector 1, 2: Manual Connector 3, 4: OnConnect
Value space: AutoShare/Desktop/Manual/OnConnect
AutoShare: While in a call, the content on the video input will automatically be presented
to the far end as well as on the local screen when you connect the cable, or when the
source is activated otherwise (for example when a connected computer wakes up from
sleep mode). You do not have to select Share on the user interface. If a presentation
source is already connected when you make or answer a call, you have to manually
select Share on the user interface.
Desktop: The content on the video input will be presented on the screen when you
connect the cable, or when the source is activated otherwise (for example when a
connected computer wakes up from sleep mode). This applies both when idle and in a
call. Also, the content on the video input will stay on the screen when you leave the call,
provided that it was the active input at the time of leaving.
Manual: The content on the video input will not be presented on the screen until you
select Share from the user interface.
OnConnect: The content on the video input will be presented on screen when you
connect the cable, or when the source is activated otherwise (for example when a
connected computer wakes up from sleep mode). Otherwise, the behavior is the same
as in manual mode.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g