Cisco TelePresence SX80 Administrator's Guide

D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
102
Cisco TelePresence SX80 Administrator Guide
Conference settings
Conference ActiveControl Mode
Active control is a feature that allows conference participants to administer a conference
on Cisco TelePresence Server using the video system's interfaces. Each user can see
the participant list, change video layout, disconnect participants, etc. from the interface.
The active control feature is enabled by default, provided that it is supported by the
infrastructure (Cisco Unified Communications Manager (CUCM) version 9.1.2 or newer,
Cisco TelePresence Video Communication Server (VCS) version X8.1 or newer). Change
this setting if you want to disable the active control features.
Requires user role: ADMIN
Default value: Auto
Value space: Auto/Off
Auto: Active control is enabled when supported by the infrastructure.
Off: Active control is disabled.
Conference AutoAnswer Mode
Define the auto answer mode. Use the Conference AutoAnswer Delay setting if you want
the system to wait a number of seconds before answering the call, and use the Conference
AutoAnswer Mute setting if you want your microphone to be muted when the call is
answered.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: You must answer incomming calls manually by tapping Answer on the Touch
controller.
On: The system automatically answers incoming calls, except if you are already in a
call. You must always answer or decline incoming calls manually when you are already
engaged in a call.
Conference AutoAnswer Mute
Define if the microphone shall be muted when an incoming call is automatically answered.
Requires that AutoAnswer Mode is switched on.
Requires user role: ADMIN
Default value: Off
Value space: Off/On
Off: The incoming call will not be muted.
On: The incoming call will be muted when automatically answered.
Conference AutoAnswer Delay
Define how long (in seconds) an incoming call has to wait before it is answered
automatically by the system. Requires that AutoAnswer Mode is switched on.
Requires user role: ADMIN
Default value: 0
Value space: Integer (0..50)
The auto answer delay (seconds).
Conference CallProtocolIPStack
Select if the system should enable IPv4, IPv6, or dual IP stack on the call protocol (SIP,
H323).
Requires user role: ADMIN
Default value: Dual
Value space: Dual/IPv4/IPv6
Dual: Enables both IPv4 and IPv6 for the call protocol.
IPv4: When set to IPv4, the call protocol will use IPv4.
IPv6: When set to IPv6, the call protocol will use IPv6.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices

System settings

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g