EasyManuals Logo

Cisco TelePresence SX80 Administrator's Guide

Cisco TelePresence SX80
183 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #151 background imageLoading...
Page #151 background image
D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
151
Cisco TelePresence SX80 Administrator Guide
Video DefaultLayoutFamily Remote
Select which video layout family to be used for the remote participants.
Requires user role: ADMIN
Default value: Auto
Value space: Auto/Equal/Prominent/Overlay/Single
Auto: The default layout family, as given by the local layout database, will be used as the
remote layout.
Equal: The Equal layout family will be used as the remote layout. All videos have equal
size, as long as there is space enough on the screen.
Prominent: The Prominent layout family will be used as the remote layout. The active
speaker, or the presentation if present, will be a large picture, while the other participants
will be small pictures. Transitions between active speakers are voice switched.
Overlay: The Overlay layout family will be used as the remote layout. The active speaker,
or the presentation if present, will be shown in full screen, while the other participants
will be small pictures-in-picture (PiP). Transitions between active speakers are voice
switched.
Single: The active speaker, or the presentation if present, will be shown in full screen.
The other participants are not shown. Transitions between active speakers are voice
switched.
Video DefaultMainSource
Define which video input source shall be used as the main video source.
Requires user role: ADMIN, USER
Default value: 1
Value space: 1/2/3/4
Set the source to be used as the main video source.
Video Input Connector [1..5] CameraControl Mode
Define whether the camera that is connected to this video input connector can be
controlled or not.
Note that camera control is not available for Connector 5 (S-video/Composite).
Requires user role: ADMIN
Default value: Connector 1, 2, 3: On Connector 4, 5: Off
Value space: Connector 1, 2, 3, 4: Off/On Connector 5: Off
Off: Disable camera control.
On: Enable camera control.
Video Input Connector [1..5] CameraControl CameraId
The camera ID is a unique identifier of the cameras that are connected to the video input.
Use the xStatus Camera API command to see the IDs of the different cameras.
Requires user role: ADMIN
Default value: Connector n: n Connector 5: 1
Value space: Connector 1, 2, 3, 4: 1/2/3/4/5/6/7 Connector 5: 1
Select the ID of the camera.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices
System settings

Table of Contents

Other manuals for Cisco TelePresence SX80

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco TelePresence SX80 and is the answer not in the manual?

Cisco TelePresence SX80 Specifications

General IconGeneral
Maximum frame rate60 fps
Supported video modes720p, 1080p
Video formats supportedH.261, H.262, H.263, H.264, H.265
Supported graphics resolutions1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecsG.711, G.722, G.722.1, G.729ab
Noise reductionYes
HDMI ports quantity5
DVI-D ports quantity1
USB 2.0 ports quantity2
Product colorSilver
Rack capacity1U
Number of persons0 person(s)
Analog signal format systemNTSC, PAL
Security algorithmsHTTPS, SSH
Ethernet LAN data rates10, 100, 1000 Mbit/s
Supported network protocolsSIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Storage temperature (T-T)-20 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 90 %
Sensor type-
Image sensor size- \
Weight and Dimensions IconWeight and Dimensions
Depth309.8 mm
Width442 mm
Height44 mm
Weight3650 g

Related product manuals