EasyManuals Logo

Cisco TelePresence SX80 Administrator's Guide

Cisco TelePresence SX80
183 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #152 background imageLoading...
Page #152 background image
D15328.04 SX80 Administrator Guide CE8.2, OCTOBER 2016. www.cisco.com — Copyright © 2016 Cisco Systems, Inc. All rights reserved.
152
Cisco TelePresence SX80 Administrator Guide
Video Input Connector [4] DviType
The official DVI standard supports both digital and analog signals. In most cases the default
AutoDetect setting can detect whether the signal is analog RGB or digital. However, in some
rare cases when DVI-I cables are used (these cables can carry both the analog and digital
signals) the auto detection fails. This setting makes it possible to override the AutoDetect
and select the correct DVI video input.
Requires user role: ADMIN
Default value: AutoDetect
Value space: AutoDetect/Digital/AnalogRGB/AnalogYPbPr
AutoDetect: Set to AutoDetect to automatically detect if the signal is analog RGB or
digital.
Digital: Set to Digital to force the DVI video input to Digital when using DVI-I cables with
both analog and digital pins and AutoDetect fails.
AnalogRGB: Set to AnalogRGB to force the DVI video input to AnalogRGB when using
DVI-I cables with both analog and digital pins and AutoDetect fails.
AnalogYPbPr: Set to AnalogYPbPr to force the DVI video input to AnalogYPbPr, as the
component (YPbPr) signal cannot be auto detected.
Video Input Connector [5] SignalType
Connector 5 can be used for either S-Video or Composite video input format. Use this
setting to configure which video format the BNC connector(s) are used for.
Requires user role: ADMIN
Default value: Composite
Value space: Composite/YC
Composite: Connector 5 is configured for composite video input. Only the BNC
connector that is labeled "Y" is used.
YC: Connector 5 is configured for S-Video input. Both BNC connectors ("Y" and "C")
are used.
Video Input Connector [1..5] InputSourceType
Select which type of input source is connected to the video input.
Requires user role: ADMIN
Default value: Connector 1 and 2: camera Connector 3 and 4: PC Connector 5: other
Value space: camera/desktop/document_camera/mediaplayer/PC/whiteboard/other
camera: Use this when a camera is connected to the video input.
desktop: Use this when the video system's monitor is the main screen for the PC / laptop
that is connected to this input. The Video Input Connector [n] PresentationSelection
setting must then also be set to desktop.
document_camera: Use this when a document camera is connected to the video input.
mediaplayer: Use this when a media player is connected to the video input.
PC: Use this when a computer is connected to the video input.
whiteboard: Use this when a whiteboard camera is connected to the video input.
other: Use this when the other options do not match.
Video Input Connector [1..5] Name
Define a name for the video input connector.
Requires user role: ADMIN
Default value: ""
Value space: String (0, 50)
Name for the video input connector.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices
System settings

Table of Contents

Other manuals for Cisco TelePresence SX80

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco TelePresence SX80 and is the answer not in the manual?

Cisco TelePresence SX80 Specifications

General IconGeneral
Maximum frame rate60 fps
Supported video modes720p, 1080p
Video formats supportedH.261, H.262, H.263, H.264, H.265
Supported graphics resolutions1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecsG.711, G.722, G.722.1, G.729ab
Noise reductionYes
HDMI ports quantity5
DVI-D ports quantity1
USB 2.0 ports quantity2
Product colorSilver
Rack capacity1U
Number of persons0 person(s)
Analog signal format systemNTSC, PAL
Security algorithmsHTTPS, SSH
Ethernet LAN data rates10, 100, 1000 Mbit/s
Supported network protocolsSIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Storage temperature (T-T)-20 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 90 %
Sensor type-
Image sensor size- \
Weight and Dimensions IconWeight and Dimensions
Depth309.8 mm
Width442 mm
Height44 mm
Weight3650 g

Related product manuals