FOR-A HVS-3800HS User Manual

25
4-3-3. Confirmation Needed Parameters
In the parameters below, the value must be confirmed by pressing a function control below
each parameter.
Parameter Menu Parameter Menu
REBOOT MU SETUP top STILL1-6 STILL
INIT MU SETUP-SYSTEM DVE STILL STILL
OU INIT OU SETUP- MODE
4-3-4. Keypad Input
You can also use the keypad to input number settings to a menu. The general procedure for
making and changing operational menu settings by keypad is as follows. Keypad numbers
can only be used to input operational parameter settings that are numerical in nature. (For
example; 100, 0, etc.)
1) Press a control below each parameter (F1 - F6) to select parameter block to be changed.
2) Lights on the keypad turn on green.
3) Next, input setting at keypad.
4) Then press ENTER to confirm the setting.
IMPORTANT
When pressing a control, press it down lightly and release it within 1 sec. Note that if
you press and hold a control for more than 1 sec., related setting will be returned to the
default setting and a beep will be heard when this happens.
 Pressing the INC and DEC buttons enables the values to be changed in single
increments.
 Pressing the CLEAR button enables the input value to be cancelled.
 To enter a negative value, first enter the value, press the +/- button, check that “ - " is
displayed, and then press ENTER.
IMPORTANT
The keypad can be used in EVENT mode, USER PATTERN mode, and SEQUENCE
mode. For details about each mode, see sections 10. "User Patterns", 11 "Sequence
Operation" and 12 "Event Memory.”
INC, DEC
Press the control corresponding to
the parameter.
DIGITAL VIDEO SWITCHER
KEYPADSYSTEM / TRANSITION
SYS
MU
SET UP
OU
SET UP
FUNC
FILE
M/E
M/E2
M/E1
TRANS
BKGD
KEY1
TRANS
BKGD
KEY1
COPY
COPY
WIPE
PAT T
KEY 2
WIPE
PAT T
KEY 2
SWAP
PASTE
KEY3
KEY3
BLO CK
ADDDEL
EVENT
INC
INC
DEC
DEC
+/-
SEQ
7
DVE-PG M
4
DVE-PST
1
WIPE-MOD
0
INS
USER
PATT
8
DVE-KEY1
5
DVE-KEY2
2
DVE-KEY3
RECA LLCLEAR
STATUS
9
PLAY
6
PAUSE
3
ENTER
OVERWRITE
WIPE/DVE
MODIFY
WIPE/DVE
MODIFY
F1 F2 F3 F4 F5 F6
DIGITAL VIDEO SWITCHER
KEYPADSYSTEM / TRANSITION
SYS
MU
SETUP
OU
SETUP
FUNC
FILE
M/E
M/E2
M/E1
TRANS
BKGD
KEY1
TRANS
BKGD
KEY1
COPY
COPY
WIPE
PATT
KEY2
WIPE
PATT
KEY2
SWAP
PASTE
KEY3
KEY3
BLO CK
ADDDEL
EVENT
INC
INC
DEC
DEC
+/-
SEQ
7
DVE-PG M
4
DVE -PST
1
WIPE-MOD
0
INS
USER
PATT
8
DVE-KEY1
5
DVE-KEY2
2
DVE-KEY3
RECA LLCLEAR
STATUS
9
PLAY
6
PAUSE
3
ENTER
OVERWRITE
WIPE/DVE
MODIFY
WIPE/DVE
MODIFY
F1 F2 F3 F4 F5 F6
Z
MEMO RY CA RD
MEN U
L
DEF
MENU
R
X
WIPE
POS
Y
RESET
JOYS TICK
DVE
ROT
ENTER

FOR-A HVS-3800HS Specifications

General

Brand	FOR-A
Model	HVS-3800HS
Category	Switch
Language	English