GRAUPNER mz-24 PRO - Page 121

Phase Setup
• PHASE Column
To set up the first phase, press the appropriate
field line in the PHASE column. In the example be-
low, Line 2, titled PHASE 2, is being programmed:
BACK
1.
2.
3.
4.
5.
PHASE 1
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
PHASE 2
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
Phase
SET
Press
The field highlights blue:
BACK
1.
2.
3.
4.
5.
PHASE 1
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
PHASE 2
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
Phase
SET
Tip
Phase 6 is on the following screen. Press the NEXT
button to view the next screen.
• NEW Button
Press the  NEW button to bring up additional
fields for the active phase line:
BACK
1.
2.
3.
4.
5.
PHASE 1
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
PHASE 2
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
Phase
SET
Press
Value fields appear in the SLOW and CTL columns:
BACK
1.
2.
3.
4.
5.
PHASE 1
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
PHASE 2
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s NULL
• NAM Button (Name)
Name or rename the existing phase title by press-
ing the NAM button at the right of the display. A
red keypad screen will appear. Refer to the Model
Name section (page 42) for instructions on using
this display. In the example below, Phase 2 was
renamed "START":
BACK
1.
2.
3.
4.
5.
PHASE 1
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s NONE
Rename Phase 1 so that announcements can be
assigned. In the example below, it has been re-
named "NORMAL":
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
Phase
SET
0.0s NULL
• CPY button (Copy)
The phase setting fields of any phase line high-
lighted blue can be copied to any another phase
line by pressing the CPY button at the right of the
display:
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
Phase
SET
0.0s NULL
Press
An active warning window appears to verify the
source/target selection:
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s KEIN
YES
NO
PHASE 2
NORMAL
SOURCE
TARGET
COPY
Press NO to terminate the procedure.
To change the target field, repeatedly press the
button in the TARGET column until the desired
phase line appears:
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s KEIN
YES
NO
PHASE 2
NORMAL
SOURCE
TARGET
COPY
Press
Press
121
Function menu | general - Phase