GRAUPNER mz-24 PRO - Page 122

In the example below, the target field was
changed from PHASE 2 to PHASE 4:
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s KEIN
YES
NO
PHASE 4
NORMAL
SOURCE
TARGET
COPY
Press NO to terminate the procedure. Press YES
to continue. The source phase information is dupli-
cated to the selected target line:
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s NULL
0.0s NULL
Change the copied phase line name information by
using the NAM Button (page 121), and/or adapt
the transferred delay or transferredswitch as de-
scribed in the SLOW Column section (page 122)
and CTL Column section (page 123).
• DEL Button (Delete)
The phase information of any phase line highlight-
ed blue can be deleted by pressing the DEL but-
ton at the right of the display. In the example be-
low, the Phase 4 information needs to be cleared:
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s NULL
0.0s NULL
Press
The Phase 4 settings disappear:
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s NULL
• SLOW Column (Delay)
Use this setting to set a delay for a smooth tran-
sition between phases. It is possible to set differ-
ent delays for changing between different phases.
For example, the time delay when moving from a
phase into Phase 3 can differ from when moving
to Phase 1.
To set the delay time, press the field for the appro-
priate phase in the SLOW column:
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s NULL
Press
The field highlights blue:
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
0.0s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s NULL
Raise or lower the value with the INC  or DEL
buttons at the right edge. The delay switchover
time can be set anywhere from 0.0 to 9.9 seconds.
In the example below, the NORMAL phase delay is
set for 1.2s:
BACK
1.
2.
3.
4.
5.
NORMAL
CPY
DEL
DEC
1.2s
NAM
NEXT
NEW
INC
START
PHASE 3
PHASE 4
PHASE 5
PHASE
SLOW
CTL
PHASE
SET
0.0s NULL
Use the same procedure with the other phase.
122 Function menu | general - Phase