GRAUPNER mz-24 PRO - Page 185

Display Page Travel Setting
The adjustment range of 100% to both sides allows
the adjustment of different deflections on the right
side independent of the rotation direction of the ai-
leron servos on this display page. 100% (travel) cor-
responds to normal deflection, and 0% (travel) corre-
sponds to the split function.
Notice
At least then, in case of use of the butterfly sys-
tem of the differentiation reduction function, a dif-
ferentiation should not be performed in this dis-
play page but by pressing the NEXT button to bring up
the Differentiation/Reduction Display Page (page 185).
To change a value, press the appropriate value field.
In the example below, the selected aileron travel must
be changed to 066%:
BACK
INC
RES
DEC
100%
100%
100%
100%
AILE1 AILE2
RATE A
RATE B
SERVO
PHASE 1 Aile di
AILE3
AILE4
100%
100%
100%
100%
NEXT
Press
The field highlights blue:
BACK
INC
RES
DEC
100%
100%
100%
100%
AILE1 AILE2
RATE A
RATE B
SERVO
PHASE 1 Aile di
AILE3
AILE4
100%
100%
100%
100%
NEXT
Press the INC or DEC buttons or the arrow keys
( pq ) to increase/decrease the value:
BACK
INC
RES
DEC
100%
100%
066%
100%
AILE1 AILE2
RATE A
RATE B
SERVO
PHASE 1 Aile di
AILE3
AILE4
100%
100%
100%
100%
NEXT
Use the same procedure to adjust the other differenti-
ation values for all remaining ailerons.
Press the  RES button to reset the changed value
back to the default.
Differentiation/Reduction Display Page
BACK
PHASE 1
SERVO
INC
RES
DEC
000%
AI1 L+R
000%
AI12 L+R
000%
FL1 L+R
000%
FL2 L+R
Di. Red.
000%
000%
000%
000%
NEXT
Aile di
Notice
The available setting options depend on the
number of ailerons selected during the basic set-
tings of the model (BASE submenu Model Type).
• Programming the differentiation
The adjustment range of 100% to allows you to
adjust different deflection on the right side inde-
pendent of the direction of rotation of the servos.
000 % (differentiation) corresponds to normal de-
flection and 100 % (differentiation) of the split func-
tion.
To set the differentiation, press the appropriate val-
ue field of the Diff. column. In the example be-
low, the selected aileron travel must be changed
to 045%:
BACK
PHASE 1
SERVO
INC
RES
DEC
000%
AI1 L+R
000%
AI12 L+R
000%
FL1 L+R
000%
FL2 L+R
Di. Red.
000%
000%
000%
000%
NEXT
Aile di
Press
The field highlights blue:
BACK
PHASE 1
SERVO
INC
RES
DEC
000%
A/1 L+R
000%
A/2 L+R
000%
FL1 L+R
000%
FL2 L+R
Diff. Red.
000%
000%
000%
000%
NEXT
AILE diff
Press the INC or DEC buttons or the arrow keys
( pq ) to increase/decrease the value:
BACK
PHASE 1
SERVO
INC
RES
DEC
045%
AI1 L+R
000%
AI2 L+R
000%
FL1 L+R
000%
FL2 L+R
Di. Red.
000%
000%
000%
000%
NEXT
Aile di
Use the same procedure to adjust the other dif-
ferentiation values for all remaining flaps/ailerons.
Press the RES button to reset the changed value
back to the default.
• Programming the reduction
A 000% value in the right column means that the
"aileron differentiation" programmed in the trans-
185
Function menu | Airplane models - Aileron settings