GRAUPNER mz-24 PRO - Page 195

Notice
The available setting options depend on the
number of ailerons selected during the basic set-
tings of the model (BASE submenu Model Type).
To save and exit, press the BACK button at the top
left of the display to return to the previous menu:
SET
CTL
ON
ON
FLAP TYP ACT
ON
FLAP
AILE >> FLAP
ELEV >> FLAP
FLAP >> ELEV
ON
INH
INH
>>
>>
>>
>>
BACK
THERMIK FLAP MIX
SERVO
Press
ELEV >> FLAP line
To support the elevatorin tight curves and aerobatics,
the flap function can be included by controlling the
elevatorwith this mixer. Select the mixing direction
so that the flaps move downward when the elevator is
pulled (up), and conversely upward when the elevator
is pushed (down).
A symmetrical or an asymmetrical effect can be de-
fined for each flap pair. Values of ±125% are possible.
The aileron uniform default values are +30%:
INC
RES
DEC
+030%
+030%
+030%
+030%
AILE1 AILE2
ON
ELEV >> FLAP
AILE3
AILE4
+030%
+030%
+030%
+030%
CTL
NEXT
RATE A
RATE B
BACK
SPEED Flap MIX
SERVO
The flaps uniform default values are +30%:
INC
RES
DEC
+030%
+030%
+030%
+030%
FLAP1 FLAP2
ON
ELEV >> FLAP
FLAP3
FLAP4
+030%
+030%
+030%
+030%
CTL
NEXT
RATE A
RATE B
BACK
SPEED Flap MIX
SERVO
Adapt the individual values as described in the FLAP
Line section (page 192).
Notice
The available setting options depend on the
number of ailerons selected during the basic set-
tings of the model (BASE submenu Model Type).
To save and exit, press the BACK button at the top
left of the display to return to the previous menu:
SET
CTL
ON
ON
FLAP TYPE ACT
ON
FLAP
AILE >> FLAP
RUDD >> FLAP
FLAP >> ELEV
ON
ON
INH
>>
>>
>>
>>
BACK
SPEED Flap MIX
SERVO
Press
FLAP >> ELEV line
When setting flaps, upward or downward torque can
arise about the transverse axis. Elevated flaps also
cause the models to fly faster. These reactions can
be achieved with the mixer.
When setting the flaps, use this mixer to have the ai-
leron position automatically track the flaps depending
on the set value.
The setting can be symmetrical or asymmetrical to the
flap control center point.
The adjustment range is ±125%. This mixers normal
settings lie within the single-digit to low double-digit
range. By default, 0% is uniformly set:
INC
RES
DEC
000%
000%
ELEV1
ON
FLAP >> ELEV
CTL
RATE A
RATE B
BACK
SPEED Flap MIX
SERVO
Adapt the individual values as described in the FLAP
Line section (page 192).
To save and exit, press the BACK button at the top
left of the display to return to the previous menu:
SET
CTL
ON
ON
FLAP TYPE ACT
ON
FLAP
AILE >> FLAP
ELEV >> FLAP
FLAP >> ELEV
ON
ON
ON
>>
>>
>>
>>
BACK
SPEED Flap MIX
SERVO
Press
Press the BACK button at the top left of the display
to return to the FUNCTION menu:
BACK
SYSTEM
BASE
FUNCTION
Phase
Wing MIX
D/R,EXPO
THR.CRV
Idle LOW
Snap roll
Prog.MIX
Aile diff
Flap MIX
Flap set
TTrainer
Airbrake
Sequence
Logical sw
V-Tail
195
Function menu | Airplane models - Flaps mixer