GRAUPNER mz-24 PRO - Page 194

CH 9.
CH 10.
CH 11.
CH 12.
NONE
NONE
NONE
NONE
INC
RES
DEC
+100%
+100%
+100%
+100%
+100%
+100%
CTL
– TRAVEL+
NEXT
BACK
SERVO
CTL Set
PHASE 1
OFFSET
000%
000%
000%
-010%
+100%
+100%
• In the OFFSET line the default offset posi-
tions of the aileron pairs are 000%:
INC
RES
DEC
+100%
+100%
+100%
+100%
FLAP1 FLAP2
000%
000%
OFFSET
RATE A
RATE B
FLAP
BACK
PHASE 1 Flap MIX
SERVO
FLAP3
FLAP4
+100%
+100%
+100%
+100%
000% 000%
These offset values must be changed in
OFFSET column of the BASE submenu
CTL Set in the CH6 line:
CH 5.
CH 6.
CH 7.
CH 8.
NONE
SL 2
NONE
NONE
INC
RES
DEC
+100%
+100%
+100%
+100%
+100%
+100%
CTL
– TRAVEL+
NEXT
BACK
SERVO
CTL Set
PHASE 1
OFFSET
000%
+015%
000%
000%
+100%
+100%
• When ACT = INH or OFF in the sub-
menu Flap set, all the provided flaps move
in the respective positions corresponding
with the settings saved in CTL Set (control
position), Flap MIX (offset value and travel
setting) and Flap set (RATE values).
• When ACT = ON in the submenu Flap
set, all the provided flaps move in the re-
spective positions corresponding with the
settings saved in CTL Set (control posi-
tion), Flap MIX (offset value and travel set-
ting) and Flap set (RATE values).
Press the  RES button to reset the changed value
back to the default.
To save and exit, press the BACK button at the top
left of the display to return to the previous menu:
SET
CTL
ON
ON
FLAP TYPE ACT
ON
FLAP
AILE >> FLAP
ELEV >> FLAP
FLAP >> ELEV
INH
INH
INH
>>
>>
>>
>>
BACK
PHASE 1 Flap MIX
SERVO
Press
AILE >> FLAP Line
Use this line to adjust phase settings for flap pair
movement when the aileron is actuated. Normally,
the flaps follow the ailerons with less deflection, with
a mixed amount less than 100%.
A setting range of ±125 % makes it possible to appro-
priately adapt the deflection direction to the ailerons
depending on the flap servo rotation direction.
Notice
Since all values are set separately, the aileron de-
flections of the flaps can also be different. When
using a glider model, it is recommended using
the "Diff." and "Red." columns in the FUNCTION sub-
menu Aile diff.
In the TRIM line, set the aileron trim action grade on
the aileron flaps function between 0 and 150%.
Set the individual values as described above. In the
example below, the values have been changed as
needed:
INC
RES
DEC
+055%
+055%
+055%
+055%
FLAP1 FLAP2
ON
AILE >> FLAP
FLAP3
FLAP4
+033%
+033%
+033%
+033%
CTL
RATE A
RATE B
+055%
TRIM
BACK
THERMIK FLAP MIX
SERVO
194 Function menu | Airplane models - Flaps mixer