GRAUPNER mz-24 PRO - Page 93

Use the same procedure for a value on the plus side
of the control travel, for example:
CH 5.
CH 6.
CH 7.
CH 8.
NONE
NONE
NONE
DV 2
INC
RES
DEC
+100%
+089%
+100%
+100%
+087%
+100%
CTL
– TRAVEL+
NEXT
BACK
SERVO
CTL Set
PHASE 1
OFFSET
000%
000%
000%
+012%
100%
100%
Press the  RES button to reset the changed value
back to the default (+100%).
Use the same procedure for the other settings.
Symmetrical Delay
Use this screen to set a time delay for the selected
control signal.
Press the NEXT button on the right side of the screen
to move to the delay screen of the CTL Set display:
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
0.0s
0.0s
0.0s
0.0s
0.0s
INC
RES
DEC
0.0s
0.0s
0.0s
0.0s
0.0s
NEXT
BACK
SERVO
CTL Set
PHASE 1
CH 6.
0.0s
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
0.0s
Press the 0.0s value field in the appropriate channel
line. In the example below, CH8 requires a 4.5s delay:
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
0.0s
0.0s
0.0s
0.0s
0.0s
INC
RES
DEC
0.0s
0.0s
0.0s
0.0s
0.0s
NEXT
BACK
SERVO
CTL Set
PHASE 1
CH 6.
0.0s
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
0.0s
Press
The field highlights to blue:
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
0.0s
0.0s
0.0s
0.0s
0.0s
INC
RES
DEC
0.0s
0.0s
0.0s
0.0s
0.0s
NEXT
BACK
SERVO
CTL Set
PHASE 1
CH 6.
0.0s
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
0.0s
The maximum value adjustment range is 9.9 seconds.
Press the INC or DEC button at the right edge of the
display to increase/decrease the value. Alternatively,
press the arrow keys ( pq ) to the left of the display
screen to achieve the same result.
In the example below, CH8 has a 4.5s delay:
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
0.0s
0.0s
0.0s
0.0s
0.0s
INC
RES
DEC
0.0s
4.5s
0.0s
0.0s
0.0s
NEXT
BACK
SERVO
CTL Set
PHASE 1
CH 6.
0.0s
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
0.0s
Press the  RES button to reset the changed value
back to the default (0.0s).
The Servo display can be accessed at any time by
pressing the SERVO button in the upper right hand
corner the screen or by simultaneously pressing the
arrow keys ( pq ) to the left of the display screen or
by. Pressing the ESC key underneath the arrow keys
brings up the previous screen.
Use the same procedure for the other settings.
Notice
Use this setting to set a symmetrical delay for the
transmitter-side control signal with the stan-
dardlabeling 0.0s. A delay set here affects the
servo with the same channel number of the delayed re-
ceiver connection as well as all servos controlled by the
control element assigned to specific control function.
93
Base menu - Control/switch setting