EasyManuals Logo

HPE FlexNetwork MSR Series Comware 5 Security Configuration Guide

HPE FlexNetwork MSR Series
547 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #423 background imageLoading...
Page #423 background image
410
[DeviceA] interface ethernet 1/2
[DeviceA-Ethernet1/2] ip verify source ip-address mac-address
# Configure Ethernet 1/2 to allow only IP packets with the source MAC address of
0001-0203-0405 and the source IP address of 192.168.0.3 to pass.
[DeviceA] interface ethernet 1/2
[DeviceA-Ethernet1/2] ip source binding ip-address 192.168.0.3 mac-address
0001-0203-0405
[DeviceA-Ethernet1/2] quit
# Enable IPv4 source guard on Ethernet 1/1 to filter packets based on both the source IP
address and MAC address.
[DeviceA] interface ethernet 1/1
[DeviceA-Ethernet1/1] ip verify source ip-address mac-address
# Configure Ethernet 1/1 to allow only IP packets with the source MAC address of
0001-0203-0406 and the source IP address of 192.168.0.1 to pass.
[DeviceA-Ethernet1/1] ip source binding ip-address 192.168.0.1 mac-address
0001-0203-0406
[DeviceA-Ethernet1/1] quit
2. Configure Device B:
# Enable IPv4 source guard on Ethernet 1/2 to filter packets based on both the source IP
address and MAC address.
<DeviceB> system-view
[DeviceB] interface ethernet 1/2
[DeviceB-Ethernet1/2] ip verify source ip-address mac-address
# Configure Ethernet 1/2 to allow only IP packets with the source MAC address of
0001-0203-0406 and the source IP address of 192.168.0.1 to pass.
[DeviceB] interface ethernet 1/2
[DeviceB-Ethernet1/2] ip source binding ip-address 192.168.0.1 mac-address
0001-0203-0406
[DeviceB-Ethernet1/2] quit
# Enable IPv4 source guard on Ethernet 1/1 to filter packets based on the source IP address.
[DeviceB] interface ethernet 1/1
[DeviceB-Ethernet1/1] ip verify source ip-address
# Configure Ethernet 1/1 to allow only IP packets with the source IP address of 192.168.0.2 to
pass.
[DeviceB-Ethernet1/1] ip source binding ip-address 192.168.0.2
[DeviceB-Ethernet1/1] quit
Verifying the configuration
# On Device A, display information about static IPv4 source guard binding entries. The output shows
that the static IPv4 source guard binding entries are configured successfully.
[DeviceA] display ip source binding static
Total entries found: 2
MAC Address IP Address VLAN Interface Type
0001-0203-0405 192.168.0.3 N/A Eth1/2 Static
0001-0203-0406 192.168.0.1 N/A Eth1/1 Static
# On Device B, display information about static IPv4 source guard binding entries. The output shows
that the static IPv4 source guard binding entries are configured successfully.
[DeviceB] display ip source binding static
Total entries found: 2
MAC Address IP Address VLAN Interface Type

Table of Contents

Other manuals for HPE FlexNetwork MSR Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HPE FlexNetwork MSR Series and is the answer not in the manual?

HPE FlexNetwork MSR Series Specifications

General IconGeneral
BrandHPE
ModelFlexNetwork MSR Series
CategoryNetwork Router
LanguageEnglish

Related product manuals