IBM 4800-741 - Page 6

Chapter 2. Installation and system setup . . . . . . . . . . . . . .25
Before you begin . . . . . . . . . . . . . . . . . . . . . . . .25
Supported operating systems . . . . . . . . . . . . . . . . . .25
Determining your configuration . . . . . . . . . . . . . . . . . .25
Your order and packaging . . . . . . . . . . . . . . . . . . . .25
Setup procedures . . . . . . . . . . . . . . . . . . . . . . . .26
Step 1. Installing your internal options . . . . . . . . . . . . . . .26
Step 2. Wide units only: Installing the expansion housing and the optional
UPS . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Step 3. Installing the cover kit . . . . . . . . . . . . . . . . . .33
Step 4. Installing the slanted I/O tray (wide units only) . . . . . . . . .38
Step 5. Routing the cables . . . . . . . . . . . . . . . . . . .39
Step 6. Attaching your I/O devices . . . . . . . . . . . . . . . . .39
Step 7. Installing the fillers on a slanted I/O tray . . . . . . . . . . . .40
Step 8. Connecting the power . . . . . . . . . . . . . . . . . .43
Step 9. Running the BIOS configuration utility . . . . . . . . . . . .44
Chapter 3. Installing internal options . . . . . . . . . . . . . . . .45
Cover removal procedures . . . . . . . . . . . . . . . . . . . .45
Top plate removal . . . . . . . . . . . . . . . . . . . . . . . .49
Installing a feature card . . . . . . . . . . . . . . . . . . . . . .50
Installing memory modules . . . . . . . . . . . . . . . . . . . .51
Chapter 4. Installing external options . . . . . . . . . . . . . . . .53
Before you start . . . . . . . . . . . . . . . . . . . . . . . .53
To install the SurePOS 700: . . . . . . . . . . . . . . . . . . .53
Attaching the cables to the system unit . . . . . . . . . . . . . . . .53
Securing IBM USB POS keyboard cables . . . . . . . . . . . . . .53
Securing the cable using cable ties . . . . . . . . . . . . . . . .54
Installing the cash drawer and the system unit . . . . . . . . . . . . .55
Non-IBM cash drawers: Setting the jumper for the correct voltage . . . . .57
Removing and replacing the cash drawer coin-roll cutter (compact cash drawer
only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Installing I/O trays . . . . . . . . . . . . . . . . . . . . . . . .59
Installing an I/O tray on the system unit . . . . . . . . . . . . . . .59
Installing a slanted I/O tray on the full-size cash drawer . . . . . . . . .60
Installing the fillers . . . . . . . . . . . . . . . . . . . . . . .60
Installing the tape-holder kit . . . . . . . . . . . . . . . . . . . .60
Installing the printer . . . . . . . . . . . . . . . . . . . . . . .62
Installing the 40-character LCD . . . . . . . . . . . . . . . . . . .63
Installing the 40-character VFD . . . . . . . . . . . . . . . . . . .66
Installing the character/graphics display . . . . . . . . . . . . . . . .68
Installing the display post with a snap . . . . . . . . . . . . . . .68
Installing the display post with a base . . . . . . . . . . . . . . .71
Installing the guidance label . . . . . . . . . . . . . . . . . . .73
Attaching an IBM SurePoint Solution . . . . . . . . . . . . . . . . .74
Installing CRT displays . . . . . . . . . . . . . . . . . . . . . .75
Installing a CRT on a wedge mount . . . . . . . . . . . . . . . .75
Installing a CRT in a slanted I/O tray . . . . . . . . . . . . . . . .76
Installing a CRT on a post mount . . . . . . . . . . . . . . . . .77
Attaching the distributed pedestal to the counter . . . . . . . . . . .78
Attaching the pedestal to the short-post mounting plate . . . . . . . . .80
Installing the large CRT table post mount to a pedestal . . . . . . . . .81
Installing and removing lock inserts . . . . . . . . . . . . . . . . .82
Preparing to install a lock or a blank lock insert . . . . . . . . . . . .82
Installing a lock insert . . . . . . . . . . . . . . . . . . . . .82
Updated October 31, 2007
iv SurePOS 700 Series: SurePOS 700-721/741/781, 722/742/782 Planning, Installation, and Operation Guide