Function Description
Queue Tone
This tone sounds from the transceiver while the transceiver is searching with the Auto Telephone
in an LTR Trunking system for an available RIC repeater to be connected. This tone sounds from
the transceiver every 1 sec until an available RIC repeater to be connected is found or Auto
Telephone is terminated if the transceiver cannot find an available RIC repeater within 60 sec.
Free System Ringback
Mode Tone
This tone sounds from the transceiver when the transceiver enters Free System Ringback Mode
in an LTR Trunking system.
Ringer Tone
This tone sounds from the transceiver when a repeater is temporarily available in Free System
Ringback Mode in an LTR Trunking system.
Priority-channel Tone This tone sounds from the transceiver when the scan is paused on a Priority-channel.
Scan Stop Tone
Pressing the Home Channel or Direct Channel key during the scan pauses the scan, and the
transceiver migrates to the Home Channel or Direct Channel. Also, pressing the Channel
Recall key during the scan pauses the scan, and the transceiver migrates to the last called Zone-
channel. This tone sounds from the transceiver at 30-sec intervals while the scan pauses.
Individual Call Mode This tone sounds from the transceiver when the transceiver initiates a FleetSync Individual Call.
Fleet Call Tone This tone sounds from the transceiver when the transceiver initiates a FleetSync Fleet Call.
Group Call Tone This tone sounds from the transceiver when the transceiver initiates a FleetSync Group Call.
Search Mode Tone
This tone sounds from the transceiver when the transceiver initiates Forced Search in an NXDN
Trunking system.
This tone sounds from the transceiver when the transceiver initiates System Search in a P25
Trunking system.
This
tone sounds from the transceiver when the transceiver starts searching for the repeaters that
can be synchronized in a DMR Conventional system.
Out of Range Tone
This tone sounds at 30-sec intervals from the transceiver when the transceiver is in the search
state,
even if 10 sec elapse after the transceiver starts searching for a control channel in an NXDN
Trunking system or P25 Trunking system.
Call Request Tone
NXDN Trunking/ P25 Trunking system:
This tone sounds from the transceiver when the transceiver initiates an Individual Call or Group
Call by pressing the PTT switch.
NXDN Conventional system:
This
tone sounds from the transceiver when the transceiver initiates an Individual Call (Individual
Call Acknowledge Request) by pressing the PTT switch.
OTAP Reactivation
Tone
This tone sounds from the transceiver when OTAP Reactivation completes.
Call In Progress Tone
This tone sounds from the transceiver if the transceiver initiates a Telephone Call, Individual Call
(Message Trunked (Enhanced)), or Group Call (Message Trunked (Enhanced)) and the
transceiver is available for communications.
Disconnect Indication
Tone
This tone sounds from the transceiver if the transceiver terminates communications with a
Telephone Call, Individual Call (Message Trunked (Enhanced)), or Group Call (Message Trunked
(Enhanced)).
Key Load Alert Tone
This tone sounds from the transceiver when Key Data is written to the Secure Cryptographic
Module (SCM) or when Key Data is deleted is from the SCM.
Transaction Confirmed
Tone
In a DMR Conventional system, this tone sounds from the transceiver when the transceiver detects
that no carrier is present after sending a Call Interrupt request message.
Bluetooth Find Device
Mode Tone
This tone sounds from the transceiver when Bluetooth Find Device is executed in Bluetooth Device
Mode and a Bluetooth-compatible device is searched.
Bluetooth Connect
Tone
This tone sounds from the transceiver when the transceiver successfully connects to a Bluetooth-
compatible device.
Bluetooth Disconnect
Tone
This tone sounds from the transceiver when the connection to a Bluetooth-compatible device is
disconnected.
Complete Tone
This tone sounds from the transceiver when the transmission successfully sends a Status
Message, Short Message, GPS data or Paging Call by operating the keys on the transceiver.
Record Stopped Tone This tone sounds from the transceiver when the transceiver exits Voice Memo Mode.
6 SOUND
6.1 Tones that Sound When a User Operates the Transceiver or When the Transceiver Status Is Changed
Common FUNC (K, F)/Ver 2.20 108
CONTENTS INDEX
To Next Page
Loading...
Need help?
General
