LAR Process Analysers QuickTOC purity - Page 6

iv User Manual QuickTOC
®
purity
ATEX 2 04E3920
LAR | PROCESS ANALYSERS AG
7.2.17.1 Data in Table Form .....................................................................................116
7.2.17.2 Daily results as a curve ...............................................................................116
7.2.18 Log...................................................................................................................... 117
7.2.19 Saving Data ........................................................................................................ 119
7.2.20 Calibrate Analog Output...................................................................................... 119
7.3 Good to know .................................................................................................................... 120
7.3.1 Password .............................................................................................................. 120
7.3.2 Software Version................................................................................................... 120
7.3.3 Abort Measurement .............................................................................................. 120
7.3.4 Furnace On - Off................................................................................................... 121
7.3.5 Automatic Temperature Control............................................................................ 121
7.3.6 Condensate pump on - off .................................................................................... 121
7.3.7 Date and Time ...................................................................................................... 121
7.3.8 Language .............................................................................................................. 121
7.3.9 Save...................................................................................................................... 121
7.3.10 User Level 3........................................................................................................ 122
7.3.10.1 PC Settings .................................................................................................122
7.3.10.2 Calibration Results ......................................................................................123
7.3.10.3 CAN Selftest ...............................................................................................123
7.3.10.4 Hardware Info .............................................................................................124
7.3.10.5 DIGITAL IN 1, 2 and 3 ................................................................................ 124
7.3.10.6 DIGITAL OUT 1, 2 and 3 ............................................................................ 125
7.3.11 Calibrations......................................................................................................... 127
7.3.11.1 Service Calibration ......................................................................................127
7.3.12 Service Parameter .............................................................................................. 129
7.3.13 Update Manager ................................................................................................. 130
7.3.14 Names and Units ................................................................................................ 131
7.3.15 Control State....................................................................................................... 131
8 Care and Maintenance .................................................................................................................. 135
8.1 Overview of Regular Care and Maintenance Actions ....................................................... 136
8.1.1 Tightness Test ...................................................................................................... 136
8.2 Protocol for Visual Inspection (Analyser) .......................................................................... 137
8.3 Care and Maintenance Tasks ........................................................................................... 138
8.3.1 Overview............................................................................................................... 138
8.3.2 Actions .................................................................................................................. 139
8.3.3 Clean Vessel for Calibration Fluid and Replace Calibration Standard ................. 141
8.3.4 Check Pump Hoses and Clean if Necessary ........................................................ 141
8.3.5 Check the Inlet and Outlet of the Control Unit for Contamination......................... 141
8.3.6 Check Ventilator for Contamination ...................................................................... 141
8.3.7 Check Reactor Foot and Clean if Necessary........................................................ 141
8.3.8 Check the Gas Cooler........................................................................................... 142
8.3.9 CleanTube Cassette Pump and Pump Cassettes ................................................ 143
8.3.10 Clean Sample Pump........................................................................................... 143
8.3.11 Adjust Sample Pump .......................................................................................... 143
8.3.11.1 Clean and Grease Bearing Pin ...................................................................144
8.3.12 Checking Measurement Values of the Standard Solution .................................. 144
8.3.13 Perform a calibration........................................................................................... 145
8.3.13.1 Perform a Gas Calibration .......................................................................... 145
8.3.14 Check and Document the Status of the Analyser. .............................................. 146
8.3.15 Check and Document a Measurement ............................................................... 146
8.3.16 Replace Pump Tubes and Condensate Tubes .................................................. 146
8.3.17 Replace Reactor Pipe or Reactor Pipe Filling..................................................... 147
8.3.18 Replace Reactor Seal........................................................................................ 149
8.3.19 Loop System Tube.............................................................................................. 151
8.3.20 Check Sample Drain Tubes and Replace........................................................... 152
8.3.21 Check Quartz Wool Filter and Replace if Necessary.......................................... 152
8.3.22 Replace Gas Filter .............................................................................................. 153