Lenze i950 - Page 485

Address Designaon Default seng Data type Factor A M
0x500A:136 Tolerance window actual posion=set
posion
upper limit
0.0000 I32 10000 -
0x500A:137 Tolerance window actual posion=set posion
lower limit
0.0000 I32 10000 -
0x500A:150 SLS1 0.0000 I32 10000 -
0x500A:151 SLS1 - deceleraon me 0.000 s I32 1000 -
0x500A:152 SLS2 0.0000 I32 10000 -
0x500A:153 SLS2 - deceleraon me 0.000 s I32 1000 -
0x500A:154 SLS3 0.0000 I32 10000 -
0x500A:155 SLS3 - deceleraon me 0.000 s I32 1000 -
0x500A:156 SLS4 0.0000 I32 10000 -
0x500A:157 SLS4 - deceleraon me 0.000 s I32 1000 -
0x500A:159 Compensaon velocity of SLS 0.0000 I32 10000 -
0x500A:160 Follower - Response to SLS 0 BOOLEAN -
0x500A:161 Speed controller limitaon (SLS) 0 BOOLEAN -
0x500A:162 Deacvate safety funcons 0x00000000 U32 H
0x500A:163 Limiter status - (Read only) U32 HX
0x500A:181 Manual jog velocity 360.0000 I32 10000 -
0x500A:182 Manual jog acceleraon 720.00 I32 100 -
0x500A:183 Manual jog deceleraon 1440.00 I32 100 -
0x500A:184 Manual jog jerk 0.00 I32 100 -
0x500A:186 Deceleraon of Halt 1800.00 I32 100 -
0x500A:187 Jerk of Halt 0.00 I32 100 -
0x500B:005 Status word - (Read only) U32 HX
0x500B:010 Actual
posion - (Read only) I32 10000 X
0x500B:011 Actual velocity - (Read only) I32 10000 X
0x500B:012 Actual acceleraon - (Read only) I32 100 X
0x500B:030 Travel range Modulo [0] U16 C
0x500B:031 Cycle length 360.0000 I32 10000 C
0x500B:032 Feed constant 360.0000 I32 10000 C
0x500B:033 Gearbox factor - nominator 1 U32 1 C
0x500B:034 Gearbox factor - denominator 1 U32 1 C
0x500B:035 Load encoder mounng direcon 0 BOOLEAN C
0x500B:065 Filter cycles of actual velocity 1 U16 1 -
0x500B:066 Filter cycles of actual posion 1 U16 1 -
0x500B:081 Keep home posion aer mains switching 0 BOOLEAN -
0x500B:082 Max. angle of rotaon aer mains switching 0.0000000000 ° I32 1 -
0x500B:132 Standsll window size (load encoder) 0.0000 I32 10000 -
0x5020:004 Source of posive hardware limit switch Digital input 4 [5] I16 -
0x5020:005 Source of negave hardware limit switch Digital input 3 [4] I16 -
0x5020:006 Source of homing switch for touch probe Digital input 1 [2] I16 -
0x5020:007 Applicaon quick stop source FALSE [0] I16 -
0x5020:008 Source of fault reset FALSE [0] I16 -
0x5020:011 TP1 source Digital input 2, posive edge [11] I16 -
0x5020:013 Reference diameter analog input 1 1000.0000 mm I32 10000 -
0x5020:020 Line velocity source External [0] I16 -
0x5020:022 Set diameter source External [0] I16 -
0x5020:023 Actual dancer
posion source Analog input 1 [1] I16 -
0x5020:030 Source of digital output 1 Ready to switch on [0] I16 -
0x5021:150 System bus diagnoscs: Cycle length (input value) - (Read only) I32 10000 X
0x5021:151 System bus diagnoscs: Posion (input value) - (Read only) I32 10000 X
0x5021:152 System bus
diagnoscs: Velocity (input value) - (Read only) I32 10000 X
0x5021:153 System bus diagnoscs: Acceleraon (input value) - (Read only) I32 100 X
0x5021:154 System bus diagnoscs: Torque (input value) x.xx Nm (Read only) I32 100 X
* Default seng depending on the size.
Appendix
P
arameter aribute list
485