What causes the Exhaust Thermistor Shorted Error in Maytag MLE22PD Washer/Dryer?
An Exhaust Thermistor Shorted Error on your Maytag Washer/Dryer means the exhaust thermistor is shorted, and the temperature is above 120°C (250°F) (
What does Exhaust Thermistor Open Error mean on Maytag MLE22PD?
An Exhaust Thermistor Open Error on your Maytag Washer/Dryer means that the exhaust thermistor is open, and the temperature drops below –8°C (18°F) (>50 k?) for 1 minute in Run mode, or immediately in Factory Diagnostic Mode.
What does COIN 1 ERROR mean on Maytag Washer/Dryer?
A COIN 1 ERROR on your Maytag Washer/Dryer indicates a blocked coin 1 or a coin drop UI control circuit failure. If this occurs, coin recognition and the customer display will be disabled while the blockage persists.
What does COIN 2 ERROR mean on Maytag Washer/Dryer?
A COIN 2 ERROR on your Maytag Washer/Dryer means there is a blocked coin 2 or a coin drop UI control circuit failure. When this happens, coin recognition and the customer display are disabled until the blockage is resolved.
Why am I getting a LOW VOLTAGE DETECTION ERROR on my Maytag MLE22PD?
A LOW VOLTAGE DETECTION ERROR on your Maytag Washer/Dryer indicates that voltage below 90 VAC was detected for 8 seconds.
General| Brand | Maytag |
|---|---|
| Model | MLE22PD |
| Type | Washer/Dryer |
| Fuel Type | Electric |
| Color | White |
| Voltage | 240 V |
| Amperage | 30 A |
| Drum Material | Stainless Steel |
| Number of Cycles | 12 |
| Wrinkle Prevention Option | Yes |
| Energy Star Certified | Yes |
| Width | 27 in. |
Provides information to enable service professionals to diagnose and repair the Maytag Commercial Stack Washer/Dryer.
Important safety messages and warnings for operating and servicing the appliance.
Explains the structure and meaning of model numbers for Maytag Commercial Stack Washer/Dryer.
Details the format and meaning of serial numbers for Maytag Commercial Stack Washer/Dryer.
Indicates where to find the model and serial number label and the tech sheet.
Details the limited warranty terms and conditions for Maytag Commercial Laundry products.
Provides physical dimensions of the Maytag Commercial Stack Washer/Dryer.
Specifies required clearances for installation and operation.
Instructions for cleaning the washer interior, exterior, and dispenser drawer.
Maintenance instructions for the dryer, including cleaning the lint screen and exhaust.
Guide to setting up and operating the electronic control panel of the washer/dryer.
Procedure for accessing and disassembling the chemical dispenser drawer and its parts.
Instructions for removing and accessing the control panel of the washer/dryer.
Steps for removing and accessing the main control board.
Procedure for removing and accessing the keypad assembly.
Tests to check the resistance of the washer's inlet valve solenoids.
Tests to check the resistance of the washer's pressure sensor.
Tests to check the resistance of the RFI line filter at the component and CCU.
Tests for the door switch, door lock coil, and wax motor at the CCU.
Tests to check the resistance of the washer's drain pump motor.
Tests to check the resistance of the washer's temperature sensor.
Tests to check the resistance of the dryer's drive motor windings.
Procedure to test the thermal fuse for continuity.
General checks and procedures before starting troubleshooting.
List of diagnostic codes for Maytag Commercial Dryer errors.
List of diagnostic codes for Maytag Commercial Washer errors.
Wiring diagram for electric models of the Maytag Commercial Stack Washer/Dryer.
Wiring diagram for gas models of the Maytag Commercial Stack Washer/Dryer.
To Next Page