453
DP-C405/C305/C265
FEB 2008Ver. 1.1
<J70~79 and J92~94 Codes for i-ADF>
J63 1. The Paper Path Sensor (PI10) does not detect paper within a predetermined time
in the Saddle. (DA-FS405/FS356/FS325)
2. The Paper Path Sensor (PI10) does not go Off within a determined time after the
sensor is activated. (DA-FS405/FS356/FS325)
(Refer to Sect 12.1.2.5. Saddle Unit)
Finisher
Saddle
J64 1. The Puncher is not activated correctly. (DA-FS405/FS356/FS325)
2. The Punch Sensor (PI11) goes On before the start of initialization.
(Refer to Sect 12.1.2.6. Punch Unit)
Finisher
Punch
J65 1. The Paper Exit Sensor (1819-27) does not detect paper within a predetermined
time in the Finisher. (DA-FS402/FS350/FS320)
2. The Paper Exit Sensor (1819-27) does not go Off within a determined time in the
Finisher. (DA-FS402/FS350/FS320)
3. The Paper Exit Sensor (1819-27) detects paper before the start of initialization.
(DA-FS402/FS350/FS320)
Finisher
J66 The Stapler is not activated correctly. (DA-FS405/FS356/FS325)
J70-79 (See the following table below)
J80 The Automatic Duplex Unit (ADU) Paper Path Sensor 0 (1819-38) does not detect
paper within a predetermined time.
ADU
J81 The ADU Paper Path Sensor 1 (1819-31) does not detect paper within a
predetermined time.
J82 The ADU Paper Path Sensor 2 (1819-07) does not detect paper within a
predetermined time.
J83 The ADU Paper Path Sensor 0 (1819-38) does not go Off within a determined time.
J86 1. The ADU Paper Path Sensor 0 (1819-38) detects paper before initialization.
2. The ADU Paper Path Sensor 0 (1819-38) detects paper before the Feed Roller
starts rotating.
J87 1. The ADU Paper Path Sensor 1 (1819-31) detects paper before initialization.
2. The ADU Paper Path Sensor 1 (1819-31) detects paper before the Feed Roller
starts rotating.
J88 1. The ADU Paper Path Sensor 2 (1819-07) detects paper before initialization.
2. The ADU Paper Path Sensor 2 (1819-07) detects paper before the Feed Roller
starts rotating.
J92-94 (See the following table below)
J96 The Printer Sequence Jam 4: System Timer detection error after Printing. Printer
J97 The Printer Sequence Jam 3: System Timer error during Printing process.
J98 The Printer Sequence Jam 2: System Timer error during Printing Preparation.
J99 The Printer Sequence Jam 1: 2-sided printing did not start after a determined time has
lapsed.
ADU
Code Contents Section
J70 The ADF Registration Sensor 1 (401-06) does not detect paper within a
predetermined time in the ADF.
ADF
J71 The ADF Registration Sensor 1 (401-06) keeps dedicating paper after a
predetermined time in the ADF.
J72 1. The ADF Registration Sensor 2 (401-08) does not detect paper within a
predetermined time after the ADF Registration Sensor 1 (401-06) is activated.
2. The ADF Registration Sensor 2 (401-08) does not detect paper within a
predetermined time after the ADF Registration Sensor 3 (401-09) is activated.
Jam Error Codes (J Code) Table
Code Contents Section
To Next Page
