Sicma TR80 - Page 52

To Next Page

To Previous Page

User and maintenance manual - SEMI-MOUNTED HARVESTER WITH TRUNK SHAKER - TR80

Rev. 0 - 05/2021

108°

84°

Figure 20 - Lateral tilting of the vibrating head

Figure 21 - Rotation of the telescopic arm

Main Page

Table of Contents5
General Information11
Introduction11
Importance of the Manual11
How to Store the Manual11
Reproduction and Copyright Restrictions12
Updating the User & Maintenance Manual12
Manufacturer's Data13
Technical Assistance Service13
Consultation Method14
Safety15
General Safety Instructions15
Warnings for Coupling/Uncoupling the Machine17
Warnings on the Cardan Shaft19
Warnings on Machine Transportation21
Warnings for Using the Harvesting Machine22
Warnings on Machine Cleaning, Adjustment and Maintenance24
Precautions for Health25
Safety Distance from Overhead Power Lines26
Intended Use27
Improper Use28
Forbidden Use29
Staff Qualification30
Personal Protective Equipment (PPE)31
Safety Signs32
Residual Risks34
Safety Devices37
Machine Description and Technical Information38
Orientation of the Machine38
Machine Identification39
Warranty Terms40
General Description40
Main Components41
Description of Main Components42
Vibrating Head42
Telescopic Arm44
Hydraulic System45
Electrical System47
Technical Characteristics49
Size in Working Configuration49
Size in Transport Configuration50
Work Areas51
Features of the Harvester53
Technical Data of the Vibrating Head54
Technical Data of the Electric System54
Technical Data of the Hydraulic System56
Sound Emissions56
Vibrations57
Machine Transport and Handling58
Transport of the Machine58
Loading and Unloading of the Machine59
Loading of the Machine by Means of a Ramp60
Loading of the Machine by Means of a Platform64
Anchoring to the Transport Vehicle67
Unloading of the Machine by Means of a Ramp68
Unloading of the Machine by Means of a Platform71
Adjustments75
Handling75
Machine Use76
Coupling to the Tractor76
Preliminary to the Coupling Phase77
Coupling of the Machine78
Connection to Power/Power Take-Off (PTO 540 Rpm)80
Electrical Connection81
Steering Wheel Control Engagement (Hydraulic Steering Aid)83
Engagement of Hydraulic Brake Control (Brake Aid)83
Uncoupling from the Tractor84
Control Panel86
Remote Control87
Controls on the Machine93
Commissioning94
Daily) Preventive Checks94
Machine Start-Up95
Operation96
Machine Operating Cycle97
Machine Start and Positioning99
Operation of the Radio Control100
Processing Steps / Vibration101
Stopping the Machine103
Short Stops103
Emergency Stop104
Maintenance105
Introduction105
Precautions105
Precautions for Hydraulic System107
Precautions for Greasing and Lubrication107
Consumables108
Product Specifications109
Routine Maintenance110
Intervention Table111
Complete Machine114
Check All Bolts and Nuts114
Cleaning the Machine115
Check of Tolerance Limits between Pins and Bushings of All Joints115
Hydraulic System116
Hydraulic Fittings Tightening Control116
Oil Leaks Check116
Check and Reset Hydraulic Oil Level117
Replacement of Hydraulic Oil Filter Cartridge118
Replace Hydraulic Oil119
Check of Wear and Efficiency of Hydraulic Pipes121
Replacement of Fittings and Hydraulic Pipes122
Speed Multiplier Gearbox123
Checking and Restoring the Lubricating Oil Level123
Lubricating Oil Replacement124
Wheels126
Wheel Jack Pin Lubrication126
Wheel Hub Lubrication127
Checking the Tightening of the Wheel Bolts128
Tyre Pressure Check128
Tires Replacement128
Electrical System129
Emergency Stop Button Efficiency Check129
Electric Cables Position Check129
Vibrating Head130
Greasing the Vibrating Head130
Greasing of Jack Pins and Jaws132
Greasing the Pins of the Vibrating Head Tilting Jack133
Greasing of the Jack Pins for Transversal Inclination (Tilting) and Spider134
Greasing the Vibrating Head Support Chains135
Vibrating Head Hardware Tightening Check136
Replacement of the Rubber Suspensor136
Replacement of Rubber Bands137
Replacement of Rubber Pillows138
Chain Replacement139
Telescopic Arm140
Greasing of the Arm Support Pin140
Greasing the Jack Pins for Arm Lifting141
Greasing of Arm Total Rotation Pins and Rotation Jack Pins142
Greasing of the Vibrating Head Oscillation Jack Pins143
Greasing of the Joint and Vibrating Head Holder Arm144
Greasing the Telescopic Extension and the Rollers145
Replacement of the Sliding Runners146
Wear of Sliding Blocks Check147
Extraordinary Maintenance147
Troubleshooting148
General Warnings148
Decommissioning150
Short Breaks150
Extended Stops/Storage150
Machine Disposal151
Optional Accessories153
Reverse Umbrella153
Attachments154
Electrical Diagram155
Hydraulic Diagrams156
Service Hydraulic Diagram156
Vibration Hydraulic Diagram157

Sicma TR80 - Page 52

Table of Contents

Related product manuals