Siemens SWT-3000 - List of Tables

To Next Page

To Previous Page

Installation and Commissioning SWT 3000 Equipment Manual

List of tables:

Table 1: Arrangement of the connecting plugs of the SWT 3000 ------------------------------------------------------------- 8

Table 2: Equipment options for slots IFC_1 to IFC_4------------------------------------------------------------------------- 9

Table 3: Arrangement of the connecting plugs of the SWT 3000 ------------------------------------------------------------10

Table 4: Pin assignment of the PU3f--------------------------------------------------------------------------------------------13

Table 5: Pin assignment for interface LIA--------------------------------------------------------------------------------------14

Table 6: Pin assignments for interface LID-1----------------------------------------------------------------------------------15

Table 7: Signals for the X-21 interface for LID-1-----------------------------------------------------------------------------15

Table 8: Signal for the G703.1 and G703.6- interface for LID-1------------------------------------------------------------15

Table 9: Pin assignments for the LID-2-----------------------------------------------------------------------------------------16

Table 10: Signals for the X-21 interface for LID-2 --------------------------------------------------------------------------16

Table 11: Signals for the G703.1 and G703.6 interface for LID-1 --------------------------------------------------------16

Table 12: Signals for the service channel interface--------------------------------------------------------------------------16

Table 13: Pin assignment of the remote access interface SSR--------------------------------------------------------------16

Table 14: Pin assignment of the remote monitoring interface SSB --------------------------------------------------------17

Table 15: Pin assignment of the CLE------------------------------------------------------------------------------------------17

Table 16: Pin assignment of the ALRS module -------------------------------------------------------------------------------18

Table 17: Connection of the alarm relays-------------------------------------------------------------------------------------18

Table 18: Pin assignment of the ALR ------------------------------------------------------------------------------------------19

Table 19: Assignment of jumpers X43 to X58---------------------------------------------------------------------------------20

Table 20: Function of the jumpers on the PU3f module---------------------------------------------------------------------21

Table 21: Selection of interfaces for the LID-1-------------------------------------------------------------------------------22

Table 22: Interface selection for the LID-2 -----------------------------------------------------------------------------------22

Table 23: Selection of the input gain for the G703.6 interfaces------------------------------------------------------------22

Table 24: Jumper setting for the input and output impedance--------------------------------------------------------------23

Table 25: Jumper setting for the receive signal gain ------------------------------------------------------------------------23

Table 26: Signification of the alarm LED on the FOM----------------------------------------------------------------------24

Table 27: Pinning of the Sub-D female connector X1 -----------------------------------------------------------------------25

Table 28: Assignment of the X4 connector for the power supply-----------------------------------------------------------26

Table 29: Assignment of the X2 connector for the alarm output -----------------------------------------------------------26

Table 30: Signification of the alarm LED on the FOB ----------------------------------------------------------------------26

Table 31: Selection of the digital interface------------------------------------------------------------------------------------27

Table 32: Setting options long haul or short haul----------------------------------------------------------------------------27

Table 33: Setting options normal mode / isolation test----------------------------------------------------------------------27

Table 34: Selection of DTE or DCE mode ------------------------------------------------------------------------------------27

Table 35: ALR indication--------------------------------------------------------------------------------------------------------28

Table 36: Functions of the ALR test switch -----------------------------------------------------------------------------------28

Table 37: Selection of the operating point for the ALRS inputs ------------------------------------------------------------29

Table 38: Selection of the relay contacts for the ALRS outputs ------------------------------------------------------------29

Table 39: Setting options for the ALR module--------------------------------------------------------------------------------30

Table 40: SWT 3000 transmit level --------------------------------------------------------------------------------------------34

Table 41: Setting options for the iSWT ----------------------------------------------------------------------------------------38

Table 42: Setting options for receiver alarm ---------------------------------------------------------------------------------41

Table 43: Setting options for measuring points ------------------------------------------------------------------------------42

Table 44: Setting options for the local clock synchronisation of the iSWT -----------------------------------------------44

Table 45: Selection of the operating modes-----------------------------------------------------------------------------------48

Table 46: Connection options of the PU3f module---------------------------------------------------------------------------48

Table 47: Setting options for RM configuration------------------------------------------------------------------------------51

Table 48: Settings of the SWT 3000 timer configuration--------------------------------------------------------------------52

Table 49: Setting options for input limitation---------------------------------------------------------------------------------53

Table 50: Setting options for input command extension to min.------------------------------------------------------------54

Table 51: Setting ranges for limiting or increasing the output time -------------------------------------------------------56

Table 52: Setting ranges for the output command extension ---------------------------------------------------------------57

Table 53: Timer settings for broadband versions ----------------------------------------------------------------------------58

Table 54: Alarm settings for broadband versions----------------------------------------------------------------------------58

Table 55: Timer settings for alternate purpose operation ------------------------------------------------------------------59

Table 56: Alarm setting for alternate multipurpose operation -------------------------------------------------------------59

Main Page

Siemens SWT-3000 - List of Tables

Table of Contents

Related product manuals