Siemens SWT-3000 - Appendix; List of Figures

SWT 3000 Equipment Manual Chapter 3: Service program PowerSys
© SIEMENS AG 2008 Edition p3_3_2x 08/09 Page - 45
Appendix
List of figures:
Figure 1:
Start of the setup program for installation of the PowerSys ----------------------------------------------------- 4
Figure 2: PowerSysWin2000 service program -------------------------------------------------------------------------------- 5
Figure 3: Functions of the PowerSys buttons --------------------------------------------------------------------------------- 5
Figure 4: Selection of the program language --------------------------------------------------------------------------------- 6
Figure 5: The create system log function -------------------------------------------------------------------------------------- 6
Figure 6: Configuration of the serial interface from the Service PC------------------------------------------------------- 7
Figure 7: Configuration for the TCP/IP connection-------------------------------------------------------------------------- 7
Figure 8: The PowerSys menu--------------------------------------------------------------------------------------------------- 8
Figure 9: Display of the print preview ----------------------------------------------------------------------------------------- 8
Figure 10: Saving the print preview in a file------------------------------------------------------------------------------------ 9
Figure 11: Selecting a file for the export from the firmware (example package 58)--------------------------------------- 9
Figure 12: The "Data source" menu --------------------------------------------------------------------------------------------10
Figure 13: Loading the data from an existing file-----------------------------------------------------------------------------10
Figure 14: Release selection -----------------------------------------------------------------------------------------------------11
Figure 15: Defining a new database --------------------------------------------------------------------------------------------11
Figure 16: Window for establishing a remote connection--------------------------------------------------------------------12
Figure 17: Menu for Firmware Release download and Dongle Upgrade--------------------------------------------------12
Figure 18: The menu Firmware Dongle Upgrade-----------------------------------------------------------------------------13
Figure 19: Selecting the dongle file by entering the name -------------------------------------------------------------------13
Figure 20: Opening the dongle file with the browser function---------------------------------------------------------------14
Figure 21: Example of an loaded PowerLink device configuration---------------------------------------------------------15
Figure 22: The PowerSys form commands-------------------------------------------------------------------------------------16
Figure 23: The event recorder in the PowerSys service program------------------- Fehler! Textmarke nicht definiert.
Figure 24: Entries in the event recorder------------------------------------------------ Fehler! Textmarke nicht definiert.
Figure 25: Starting the MemTool installation ---------------------------------------------------------------------------------21
Figure 26: Starting the MemTool program ------------------------------------------------------------------------------------22
Figure 27: Target selection-------------------------------------------------------------------------------------------------------22
Figure 28: MemTool general settings-------------------------------------------------------------------------------------------23
Figure 29: Target Setup ----------------------------------------------------------------------------------------------------------23
Figure 30: Setup Mapping--------------------------------------------------------------------------------------------------------23
Figure 31: Setup Program--------------------------------------------------------------------------------------------------------24
Figure 32: Setup Verify -----------------------------------------------------------------------------------------------------------24
Figure 33: Copy of the AllInOne*.jnk files from the firmware folder to the Memtool targets---------------------------25
Figure 34: The CSP board -------------------------------------------------------------------------------------------------------26
Figure 35: Memtool with the PowerLink target -------------------------------------------------------------------------------27
Figure 36: Selecting the Siemens PowerLink-CSP target --------------------------------------------------------------------27
Figure 37: Display after the connection to the PowerLink has been established -----------------------------------------28
Figure 38: Selection of the AllInOne files --------------------------------------------------------------------------------------28
Figure 39: Display of the sections in the list box after the Add Select has been executed -------------------------------29
Figure 40: Starting of the programming process------------------------------------------------------------------------------29
Figure 41: Display after a successful programming--------------------------------------------------------------------------30
Figure 42: Starting the firmware download------------------------------------------------------------------------------------31
Figure 43: Display of the PowerSys FW Release------------------------------------------------------------------------------31
Figure 44: The vMUX board-----------------------------------------------------------------------------------------------------32
Figure 45: Memtool with the vMUX target-------------------------------------------------------------------------------------33
Figure 46: Selecting the Siemens PowerLink-vMUX target------------------------------------------------------------------33
Figure 47: Display after the connection to the vMUX has been established-----------------------------------------------34
Figure 48: Example for selection of the AllInOne files -----------------------------------------------------------------------34
Figure 49: Display of the sections in the list box after the Add Select has been executed -------------------------------35
Figure 50: Starting of the programming process------------------------------------------------------------------------------35
Figure 51: Display after a successful programming--------------------------------------------------------------------------36
Figure 52: Starting the firmware download------------------------------------------------------------------------------------37
Figure 53: Display of the PowerSys FW Release------------------------------------------------------------------------------37
Figure 54: Position of the jumpers on the PU3 module ----------------------------------------------------------------------38
Figure 55: Start up from Memtool program with the target Siemens SWT 3000-Pu3 ------------------------------------39
Figure 56: Selecting the target file Siemens SWT 3000-PU3 ----------------------------------------------------------------39
Figure 57: Display of the selected FLASH module after connection of a SWT 3000 -------------------------------------40